A DIY clothes dryer will cost several times less than a purchased one, but it may not be any worse. Today, choosing a place to dry clothes is no longer a big problem. Almost every apartment has spacious loggias, and the height of the walls allows you to place a clothes dryer under the ceiling without taking up much space in the house. Prices for these products depend on the material, functionality and manufacturer. But! You can make an original dryer at home, using only available materials.
Where is the best place to place the dryer?
Wall-mounted dryers save home space, hold a lot of things and when folded do not create obstacles in everyday life. Suitable for placement in any convenient place: on a balcony, loggia, in bathrooms and living spaces. Dryers of this type are mounted on a load-bearing wall.
Important! Mounting a homemade clothes dryer on partition walls is unacceptable - the weight of the laundry can cause it to fall and damage the finish.
Ceiling-mounted drying devices are usually placed on balconies, loggias, and bathrooms. Due to the fact that they are mounted on the ceiling, they do not interfere with the use of the room.
Floor dryers are characterized by mobility, so they can be installed in any room. In working condition they take up a lot of space, which is why they are not recommended for use on the balcony or in the bathroom.
Care advice
Do not forget that the dryers presented here are made of wood , which does not allow them to be used outdoors. As an option, if necessary, you can place dryers under a canopy, which will protect from water precipitation.
The same applies to handling dryers indoors - if you dry things on them that have not been wrung out of water, they will get damaged.
We sincerely hope that this master class was useful and you chose the dryer option that is right for you.
We also have a master class on how to make an outdoor clothes dryer - like the one in the photo below
How to make a clothes dryer with your own hands
Before you get started, you should:
- determine the maximum weight of laundry for which it will be designed;
- decide in which room it will be located;
- see what materials are available;
- Having decided on a suitable model, you should familiarize yourself with how best to make it by studying tips and recommendations.
Wall dryer
The following materials will be required:
- For the base that will be mounted on the wall, you can use moisture-resistant plywood, a board with a joint groove, laminated chipboard, or a shelf from an old cabinet.
- Sanded bars and slats.
- Locking lock, hinges (2), folding mechanisms (2), hooks, hanging fastenings (2).
- Nails or screws.
- Varnish, enamel - to choose from.
- Carpenter's glue.
The work is performed in the following sequence:
- Create a drawing of the future structure with dimensions, taking into account that the optimal distance between the planks is 8-9 cm.
- Saw off 4 bars and strips of the required size. Treat the rough surface with sandpaper or an angle grinder (grinder).
- Drill blind holes for the planks symmetrically in two bars. If the planks have a square or rectangular cross-section, round the edges.
- Coat the holes with glue, assemble the frame together with the slats, fasten with nails or self-tapping screws.
- Make the base 10-15 cm larger than the frame.
- Paint the structure or varnish it.
- Screw on the locking lock on the top side of the base, on the back side - fastenings for hanging, on the side - a folding mechanism, at the bottom - the required number of hooks, just above which fasten the loops, and on them the frame.
Folding floor
Necessary materials:
- bars;
- furniture screws (4), partially threaded bolts (2);
- clothesline;
- paint (varnish).
Sequencing:
We recommend:
How to clean rabbit fur at home
- Assemble two U-shaped structures. To do this, you need to saw off 4 bars of equal length for the vertical sides and three for the horizontal crossbars. The second cross member is made shorter than the first by two beam widths, the third (central) by four.
- Drill holes in the top of the vertical bars and at a distance equal to 1/3 of their length, marked from the bottom.
- Based on the length of the bolts and screws, make holes under them at the ends of the crossbars.
- Drill symmetrical holes for the cord in both crossbars at equal intervals.
- Paint all the parts and, after drying, assemble the structure.
- Pull in the cord.
Homemade ceiling options
Necessary materials:
- bars (2);
- round or rectangular strips (5);
- wood screws, screws with a ring (3);
- clothesline;
- varnish or enamel.
Progress:
- Saw off 2 bars of the same length and 5 planks.
- Paint the resulting parts in 2 layers.
- On both sides of the center of the block, mark marks every 10 cm, drill through holes and insert strips into them.
- If the plank is rectangular in cross-section, then you can screw them in with self-tapping screws along the marked marks, overlapping.
- Drill 2 holes for dowel-nails on the ceiling and one on the wall.
- Tie ropes to the resulting structure, pull them through the rings on the ceiling and tie them to a screw with a ring on the wall.
Important! By untying the ropes, you can move the structure to a convenient height.
Frame with crossbars
Connect one part B to two parts A using wood glue and self-tapping screws. Apply glue to the ends of the crossbars and insert them into the prepared grooves. Check the correct connection of the frame using a construction angle, checking the right angle. Let this piece dry. Attach the crossbars to the second part B on top, and connect it to parts A using glue and self-tapping screws.
The money tree pleases with lush flowering: my secret is in caring for the leaves
Smooth and fresh skin: dermaplaning, or why a woman needs to shave her face
It’s good to wash often: myths about shampoo and hair care that only harm
Homemade drying rack from hangers
Materials:
- an old curtain rod along with the rings, fasteners and plugs on it;
- hangers;
- screws assembled with dowels.
Progress:
- Inspect the cornice mounting system and make appropriate marks on the ceiling.
- Drill holes according to the marks, insert dowels and screw the cornice to them with self-tapping screws.
- Hang the hangers on the curtain rings and secure the joints with electrical tape.
Important options to select
Making delicious and healthy marshmallows
For an electric dryer to become a truly good helper during the harvest season, it must be:
This will be influenced by the number and volume of pallets or surface area. Options for dryers up to 5 trays are a good choice for a small family. They are capable of drying several kilograms of food at a time. For more serious harvests, devices with 6 or more tiers are purchased. Models with 15-20 sections are capable of drying up to 15 kg of fresh food.
Allows you to dry various fruits and vegetables
Directly depends on the capacity of the device. A good option are 350-600 W models, which have sufficient capacity, efficiency, and do not consume a huge amount of energy.
You can set the desired temperature
Makes it possible to preserve all the beneficial properties and vitamins in products. Many convective devices are available with fixed 3 modes:
- 30-40С (Low) – light load
- 45-55С (Medium) – average load
- 60-75C (High) – high load
The last 2 modes are relevant for preparations from vegetables, fruits, berries, mushrooms, meat, and fish.
Plastic dryer for vegetables and fruits
Available in 2 main versions:
- metal – strong, reliable, durable; has significant weight; may get warm during operation
- plastic – light in weight, easy to clean
Plastic models are easy to assemble and disassemble, make it possible to increase the number of tiers, and are also transparent, which is convenient for monitoring the drying process.
With mechanical control
- the electronic view is equipped with a touch screen and keys for convenience; less exposed to pollution; adjustment is more precise
- mechanical appearance is reliable
Horizontal arrangement of trays is a more convenient option
- Trays are located vertically (one above the other) in many convective type electric dryers. Heating can be from above or below. The first option is more durable and easier to maintain, because... nothing gets on the heating block. Although devices with bottom heating cope well with large volumes of products
- horizontal arrangement of pallets is more convenient. Trays can be easily removed without affecting others. The heating block is located on the rear wall. It is also possible to simulate the chamber space by removing the pallets altogether. This way you can place large items, such as yogurt jars.
It is possible to make pastille
- the ability to prepare marshmallows or dry-dry meat and fish
- Thanks to the system of independent supply of hot air to each of the pallets, there is no need to swap them during drying
- There is no risk of getting over-dried food if the device has an auto-shut-off timer
- a device with overheating protection will be safer and last longer
- the adjustable height of the trays is useful, for example, for mushrooms, in order to dry them without chopping them
Good quality sofas: how to choose a universal model for relaxing and sleeping. Popular manufacturers + Reviews
What tools are needed
The minimum list of tools that you can use:
- hammer drill (+ drills and bits for self-tapping screws);
- hacksaw;
- roulette;
- pencil.
Of course, it will be easier and faster to make and install a dryer if you mechanize the process as much as possible: use a circular saw or jigsaw, grind wooden structures with an angle grinder, screw in screws with a screwdriver.
Nowadays, a clothes dryer is an indispensable thing in the house. But the stronger and better the material, the more expensive it is. Basically, dryers are made of plastic, aluminum - the cheapest and short-lived, stainless steel and steel - are much more expensive. If it is not possible to purchase a better quality dryer, you should try making one at home using improvised materials. It's not as difficult as it seems at first glance.
Rate this post
Radiator grille
Shoes get wet quickly but dry slowly - this depressing fact makes many people think about how to speed up this process.
Often they simply put wet boots on the radiator, but this can affect them in the most negative way. The fact is that boots dry unevenly near such a heat source. Moisture evaporates only from the outside, remaining wet inside. This leads to shoe deformation and cracking. If some parts are glued, they may simply fall off.
To avoid negative consequences, you can make your own device for drying shoes using a radiator. To do this you will need: several slats with a thickness of 0.5 cm, nails and soft synthetic fiber cloth.
You can quickly build a device using a hammer, sandpaper, an electric jigsaw and a construction stapler.
- First you need to make a diagram of the dryer.
- Then you should measure the required length from the rail and cut it.
- The internal dividers are nailed only after the side ones are attached. There should be a small distance of one centimeter between the slats.
- To avoid damaging the battery, a soft synthetic fabric is attached to the homemade dryer. A construction stapler will easily cope with this task.
- To secure the slats to the radiator, you can make hooks from leftover wood.
This drying method does not allow your favorite pair to come into contact with the surface of the radiator. Therefore, it dries evenly, without the risk of being spoiled.
