How to stretch a clothesline on a balcony

How to choose clotheslines for the balcony

The cheapest synthetic models are often flimsy. Therefore, it is important to pay attention to the material from which the product is made:

Cotton is durable, but absorbs water and dirt, so it can leave black streaks on your laundry.
Jute cord is similar in properties to cotton; it is a natural material made from plant fibers. It is capable of absorbing moisture and dyes, but over time traces of paint may appear on clothes.
Polypropylene - unlike cotton, does not stain clothes.
Metal cable with PVC braid - steel threads intertwined into one cord, covered with a polymer sheath. The cable is useful for drying down jackets and heavy blankets; it does not sag under the weight of clothes.
The cord is plastic - does not absorb water and does not get dirty. But it stretches quite quickly and begins to sag. The weight of coats and blankets cannot withstand.

The simplest method of fastening is to nail two nails and stretch a cord between them. But the technique has many drawbacks, so it has not been used for a long time. This method of fastening does not look aesthetically pleasing; over time, the rope will begin to sag and sink lower and lower.

Therefore, they often resort to various factory drying systems.

How to choose a reliable system

The cheapest option is a model with plastic strips. It is lightweight, but not suitable for heavy items. Aluminum is durable and can withstand heavy loads, but over time it begins to stain clothes. Therefore, it is advisable to choose dryers made of stainless steel or aluminum with a protective layer.

If you receive guests or have tea parties in the loggia, it is better to place a folding system. In this case, it is installed somewhere on the side or on the ceiling. It is important to consider the load-bearing capacity of the walls or ceiling. A wall made of porous concrete will not support a lot of weight; it will have to be strengthened or a floor version installed.

If you plan to dry large volumes of clothes, and the room is practically not ventilated, you will have to think about forced ventilation. This problem occurs if the balcony is located inside a cramped courtyard, where gusts of wind do not reach.

Many beautiful and elegant solutions are not designed to hold a lot of weight. For example, a console dryer with a scissor mechanism can withstand no more than 10 kg of wet clothes. Folding console models have even less load capacity - up to 5 kg. If you plan to wash down jackets, heavy bedspreads, and fur coats, it is better to take the Liana system to the balcony. It can withstand weight up to 20 kilograms.

Rope is a consumable item. You will have to accept that it will stretch during use. After a certain time, it will have to be replaced with a new one. Cords do not sag in console systems equipped with a tension drum. However, there are cheap options with a low-quality mechanism that is unable to combat sagging.

Nine criteria for choosing clotheslines

First of all, you need to take into account the strength and calculate how many kilograms of laundry you plan to hang at one time. The next factor is resistance to biological factors, such as fungus and mold.

Another important parameter is inextensibility, otherwise the clotheslines on the balcony will sag from constant loads. The product should not absorb dyes, otherwise after washing colored items, the rest of the clothes will be stained.

It is important that the design of the rope matches the style of the balcony.

The load-bearing capacity must correspond to the weight of wet items. Sometimes better quality thin twine is stronger than thick rope.

Equally important is resistance to weather conditions, such as low or high temperatures. The fibers of the twine should not damage the fabric, for example, silk fabric will form snags when it comes into contact with jute rope.

The last criterion is that the rope material should not leave an odor on things. This sometimes happens if you purchase a cord with a low-grade PVC coating.

Outdoor clothes line design for drying clothes on balcony

The buyer of rope should remember that there are two types. We are talking about material for indoor and outdoor use. The difference between them is at the level of ability to withstand prolonged exposure to the vagaries of nature.

Fabric for external use is attached to a balcony or open loggia, which reduces the load on the available space.

Regardless of the type of room and the characteristics of the laundry, the balcony will require reliable brackets. The stronger the fastening, the less likely the laundry will fall.

The following recommendations will help you achieve a good result:

Fix strong steel brackets on both sides of the balcony;
Purchase corners made from similar material in the store;
You need to make sure that the corners are equipped with holes that allow you to securely tie the clothesline;
In order to simplify the process of hanging laundry, the profile with corners should be placed not perpendicularly, but at an angle;
It would not be superfluous to install a spacer that does not allow the profile to deform.

Peculiarities

The operating principle of such schemes is inherent in the definition itself. When one or both ends of the rope are pulled, the knot is tightened. Moreover, the stronger the force, the stronger the connection will be. But it should be remembered that some self-tightening knots “work” reliably only with constant tension. If the force is expected to vary or be jerky, the connection may become loose.

Self-tightening knots are tied around any reliable support. They hold especially well on a non-slip cylindrical base: tree trunk, stump, branch, power pole and the like. The simplest knitting pattern involves only three movements. Form a half ring by twisting the free end around the base.

Continuing the movement, he is brought under the main rope and passed into the now formed loop. Essentially, this is the same knot as when tying shoelaces. But in the loop formed during its formation there is support. Now, when pulling the main rope, the free end will be pressed against a hard surface, which will prevent the structure from untying.

Preparing for work

Of course, before stretching the clothesline on the balcony, it is advisable to carry out a series of preparatory works, namely, prepare the holding brackets and install them in a given place.

Moreover, if we talk in more detail about the first part of the work, then it is more justified to use rolled metal (angle, U-shaped profile, etc.) as brackets for securing the clothesline, although in some cases (with a light load) they can be used as such elements alternative materials can also be used, be it a wooden beam, a metal pipe, or a perforated lath.

As for the preparation of the elements holding the rope, it consists in simply drilling holes in the body of the material in increments of 120 - 200 mm. Moreover, taking into account the purpose of these holes (a rope is threaded through them), they should be located strictly symmetrically on both opposite brackets. If we talk about the diameter of the holes, then it should be larger than the size of the rope in order to ensure free insertion of the material.

In addition to making perforations for fixing the clothesline, at the preparation stage you should drill holes to directly attach the brackets to the fence structures. And of course, open the resulting paintwork structures for exterior work (rust will not stain the laundry).

The installation of holding profiles should be carried out in such a way that it is convenient to dry the laundry in the future. That is, based on individual factors (type of structure, physiological characteristics of the user, etc.), it is necessary to select the most suitable location and install the brackets. Moreover, if these structures are planned to be fixed to the wall, then it is advisable to use anchor bolts or dowels with screws (with a diameter of at least 6 mm). When the brackets are located on the outside of the balcony or loggia, it is more justified to fix the material using hardware (M8, M10), using at least two on each side.

Application

Self-tightening knots are used not only by climbers and sailors. Some sources claim that there are about twenty such schemes. Knowing them all is not necessary even for a professional. But some universal combinations can be useful to the common man.

When relaxing outdoors, the “constrictor” knot will securely secure the hammock, and the “gazebo” will help to equip a canopy from the rain. For housewives, there is a “burlak sea loop” if there is a need to tighten a clothesline from sagging or organize drying for collected medicinal herbs. When walking your dog, sometimes it becomes necessary to leave your pet securely tied to a support for a while. A simple cow knot will do the trick. It knits easily and quickly allows you to release the leash.

Self-tightening fishing line knots are a must have in any fisherman's arsenal. They are also useful for securely fastening the boat. For those going on a mountain hike, knowledge of the components for belay equipment is simply necessary.

Plastic and polypropylene rope - a budget option

The clothesline for the balcony, the photo of which you see below, is made of plastic. It is created specifically for drying clothes. For convenience, it is usually armed with hooks. These ropes are quite strong and cheap. Over time, they stretch a little, but without any special problems they can be tightened again. Plastic ropes come in a variety of colors and fit well into any interior design.

Ropes made of polypropylene fibers are also quite cheap and wear-resistant. They are also made in a wide range of colors, are environmentally friendly, do not electrify and are very comfortable to use.

Which ropes are better?

For every business person, an important question is: what rope to choose for drying so that it lasts a long time and does not lose its appearance. It is recommended to pay attention to such features as strength and wear resistance. It shouldn't stretch. The most suitable options for drying clothes lines:

A metal cable in a polyvinyl chloride sheath will be strong and durable. The material is not subject to deformation, is moisture resistant, and does not stain things. The only caveat is the high cost.
The plastic cord is moisture resistant and does not stain laundry. Disadvantage: after some time, the tension disappears and the rope sags under the weight of the clothing.
Polypropylene rope has good wear-resistant properties and does not deform. The product has a favorable price/quality ratio.
Jute cords are durable, environmentally friendly, and their surface is not electrified.
Cotton rope is a durable and environmentally friendly product. Due to the influence of moisture, it quickly loses its appearance and dust stains appear on it, which can leave dark marks on clothes.

Synthetic fiber rope is more durable and does not stretch when wet. The surface layer is less susceptible to contamination. Such a rope can be cleaned of dust with a wet cloth.

Types of ropes

Nowadays, a clothesline for a balcony can be divided into types that have different shapes and structures. To understand exactly what type of rope is needed, you should familiarize yourself with the types of accessories:

A sheathed cable is several metal threads that are woven together and covered with a polymer layer. Such a balcony rope on the balcony will be a reliable assistant. Due to its strength, it is not subject to stretching under the weight of the laundry. For this reason, you can safely use this design to your advantage.
Plastic type of rope - can also be used, but how to stretch a clothesline on a balcony? The answer is quite simple: it is attached between two profiles. To visually make the structure more beautiful, ropes of different color shades are installed. The downside of such clotheslines is the high likelihood of sprains.
A polypropylene clothesline for a balcony, according to experts, is considered the most convenient to use. Its advantages are practicality and variety of colors.
Jute type of thread - made from environmentally friendly elements. A large number of mothers believe that such a rope on balconies for drying clothes can be used equally for both adult and children’s clothes. It is inferior in strength to previous types.
Twisted cable is a traditional type, as it is used in most cases due to its low cost. It is easily attached to the walls and can be quickly dismantled if necessary. The downside of this drying element is sagging, so you often have to tighten the rope.

How to securely tension a clothesline? Recommendations

Ropes with clothes drying on them that break at the wrong time can cause the housewife a lot of trouble. That's why it's so important to know how to pull a clothesline correctly and tightly. More details on how to tighten a clothesline are described below. First of all, you need to decide where it will be located. For example, in the hallway there will probably be a couple of nails or cabinet racks will be convenient for pulling rope. But on a balcony, loggia or in a special drying rack in a private house, it is best to organize a special permanent, convenient mount. Then you can leave the rope on it for the entire time or simply tighten it as needed. If there are no nails or other protrusions at the required distance in the apartment corridor, then they can be driven in. It is best to disguise these details as decorative elements and hang, for example, family photographs on nails in your free time from drying.

It’s quite easy to create special fastenings for a rope on which clothes will be dried, even with your own hands. To do this, you will need to take a strip no more than 7 centimeters wide and cut two even sections from it. The length of this part depends on the size of the drying space. The more laundry you plan to hang, the longer it should be. Next, fastenings for the slats are arranged on exactly opposite parts of the wall. It is best to use dowels for this. It is very important to choose places for them so that two opposite parts are placed clearly opposite each other. To do this, you will have to measure and recheck the distance several times. Otherwise, all the work will simply be done in vain.

Depending on the length of the slats, they can be attached either only at the edges, or in 2-3 places at once. Next, they are carefully marked with a marker. The first marks will be about 4 centimeters from the edge, and the rest will be about 20 centimeters apart. Small nails are driven in at equal intervals into the resulting marks. You can also use special hooks instead, which are not driven in, but screwed. The main thing is not to use low-strength parts with an adhesive layer. Next, you will need to tie the rope to the first nail of the selected rail. Part of it must be left hanging freely (approximately 20 centimeters). The rope is knitted with any convenient knot, the main thing is that it is as strong as possible. It is then moved to the second part of the structure, tensioned again and wound around its first nail. After this, the rope is attached in the same way to the second nails of the first and second slats.

The strongest knot should be on the last nail. It is best to choose double. After cutting the rope, it is recommended to leave a small section free on the opposite side - a kind of “tail”. This way you will get a very strong and durable “drying rack”, on which you can easily hang even the heaviest clothes, as well as bedspreads, bedding and other similar products. In this case, you won’t have to worry that the rope will break and all your clean things will end up on the floor or ground. The main thing is to devote enough time and attention to all fastenings. And also do not skimp on rope and do not use an old product that is rotten and frayed in places.

Often there is no place in the hallway for drying clothes after washing, so housewives prefer to hang them in the bathroom on ropes located right in the middle of it. But you shouldn't do this. There are no windows in the bathroom, so ventilation is impossible. As a result, fungus will quickly settle on the walls of the room and begin to actively multiply. This is especially dangerous if there are small children living in the house. To dry clothes in the bathroom, it is permissible to use only a “coil”, which, thanks to hot water, remains “hot” at any time of the year. In a private home, it would be important to organize a dryer outside. To do this, you can dig two pillars opposite each other or even arrange several of them in a circle. Next, nails are driven into the posts to tighten the ropes. Drying in the fresh air will be the most favorable for laundry. This will allow you to remove it from the ropes not only dry, but also fresh and smelling good.

Structures for tensioning ropes

The simplest design is a wooden block with a cross-section of 40 x 40 mm with screws screwed into it or nails bent into half rings, which are attached to the side walls at the required height.

The disadvantage of this design is that it can only be mounted on a loggia, that is, a recessed balcony with walls. For open, unglazed balconies or balconies with panoramic glazing, this design will not be suitable, since there will be nowhere to fix it. Then “U”-shaped trapezoids come to the rescue, the vertical posts of which are attached to the balcony parapet, and the horizontal part is used to tension the ropes on the balcony.

Such a simple structure can be made from the same wooden block 40 x 40 mm or from a metal corner.

To attach the parapet to the fence, you can use wire or metal clamps. Attach to a parapet made of a concrete slab or brick using long self-tapping screws screwed into PVC dowels.

The second most popular method is to attach ropes to screw loops screwed into the balcony wall. Unlike a bar with loops, you will have to drill a slightly larger number of holes in the wall to tighten the ropes, but shiny, neat loops look more aesthetically pleasing.

These designs are static and do not imply any automation. If the ropes become slack, they can only be tightened again by tying the ropes again.

Fishing: how to make a self-tightening knot

Oddly enough, to secure the end of the fishing line (cord) to the reel, in principle, you can use the same simple scheme, especially if you additionally reinforce it with two or more “half-pins”, and in addition, put a layer of adhesive tape on top. However, fishermen usually use a different scheme for this - with a tightening loop.

For the convenience of such fastening, the spool is removed from the reel. At the end of the fishing line, a loop is knitted in any convenient way. It is best to do this with a figure eight, but this is not important. After this, at some distance (15-20 cm) from the knot formed, the main line is grabbed, folded in half and threaded through the eye.

The new loop thus formed is pulled to a sufficient distance so that the diameter of the circle allows it to be put on the spool. Self-tightening knots on the reel with a sealing loop, on the one hand, will keep the fishing line from slipping, and on the other, allow it to be removed and changed if necessary, without cutting the connection. If the loop still slips, it means that it was placed on the wrong side when putting it on the spool, and it should be turned 180 degrees.

Installation of the drying structure

When installing outdoors, you need to pay attention to the reliability of the fastening. The design must support the weight of wet laundry, which may increase due to precipitation (rain, snow). There must be reliable painting so that when hanging, rust does not stain the laundry.

Installation of a device for drying clothes on a balcony, which was purchased in retail chains, is carried out according to the included instructions. Usually the kit includes fastening elements (brackets, dowels). The main thing is to follow all the manufacturer’s recommendations.

If the required structure must be made independently, then success depends on the skill of the performer. As a basis, it must be assumed that the structure consists of two equally spaced planks. These slats can be made of any material that can withstand the weight of the laundry and the tension force. The shape of the plank is varied: rectangle, corner, channel, tee, circle.

Industrially manufactured rope design option

For example, one of the simplest structures is two corners mounted on opposite walls. Holes with a diameter larger than the rope itself are drilled in the corner shelf. It is then inserted into the holes and pulled tight, and the ends are tied into a knot.

Internal systems

It is designed to hang clotheslines on the balcony, which will save things from various threats from the outside. This internal type includes a large number of different inventions, each of them is imperfect, but their successful combinations provide a good chance to compensate for some shortcomings.

Wall structures

These are the most popular designs if there is furniture on the balcony or the floor is occupied by other necessary items. Before choosing such models, it does not hurt to evaluate the wall surfaces in advance, since in old buildings they are often far from ideal. There are simply an “intimidating” number of wall-mounted systems, so it is better to focus only on the most popular devices for drying clothes.

Inertia dryers

They are easy to install, lightweight and convenient to use. Inertial systems consist of 2 parts: a bar, which can be stationary or temporary, and a housing with a drum, which makes it possible to tighten or loosen the ropes. Manufacturers guarantee that their “brainchildren” are able to cope with 5-6 kg of laundry.

This design has one drawback, and it’s difficult to call it insignificant. This is the low quality of the “heroines” of this article - ropes: they tend to sag. But this fly in the ointment does not scare away buyers.

Sliding systems

These are metal tubes with clotheslines between them. They are a good option for spacious balconies because they can support weights of up to 10 kg. Multifunctional devices allow you to hide the unused structure, so the appearance of the balcony on ordinary days (without washing and drying) will not be affected.

Ceiling models

Clothes dryers mounted on the ceiling of a balcony or loggia are one of the most popular models. They consist of two slats with crossbars or ropes attached to them, on which laundry is hung.

There are two main types of ceiling dryers for balconies:

With independent suspension of each bar. The most popular models in this group are called “Liana” and GIMI Lift. This is the same design, it’s just that the manufacturers are Russian (Liana) or foreign. They are easy to use, as they allow you to lower and raise one bar at a time, and place them at different heights. Clothes dryer with ceiling mounting
Single suspension for the entire structure. Several crossbars (from 2 to 6) are mounted on telescopic hangers. They can only be lowered and raised together.

The second option is easier to install, has a lower cost, but is less convenient. All planks are at the same height. This makes it difficult for laundry that is located closer to the wall or in the middle rows to dry. The second point: it is not so easy to lift a dryer loaded with wet laundry.

This is a “Liana” with a ceiling mount

Free-hanging dryers are a little more difficult to install. All crossbars are attached to two slats on the ceiling, but each of them has a rope, which allows you to lower/raise the rods for hanging laundry. So during installation, in addition to installing the crossbars on the ceiling, you also have to attach a plank to the nearby wall on which the ropes are fixed. The crossbars in ceiling dryers of this type can be made of plastic, steel coated with powder enamel (Gimi) or aluminum (Liana). You can find wooden crossbars from other manufacturers, but those listed above are represented by a large number of models.

Choosing a system for drying clothes

A clothes dryer on the balcony allows you to place a large batch of clothes. The linen jumpers are arranged in several tiers, so the structure does not take up extra space. There are two types of ready-made structures for balconies - internal and external. The most common and convenient are internal ones, installed under the roof of a balcony or loggia.

For the summer season, external modifications attached to the balcony railing are suitable. But long sheets can hang low, reaching your neighbors' windows. In the rain, clothes will get wet, and on the lower floors they will absorb road dust.

Outdoor dryers also have advantages:

Wet clothes dry faster because they are well blown by the wind.
Space on the balcony is saved, the room is not cluttered with drying linens.
If laundry is dried below window level, it does not interfere with natural light.

Typically, external fastenings are installed only on high floors. Hanging sheets attached to the outside are unattractive and create a fire hazard. If a careless neighbor on the top floor throws a cigarette butt, there is a chance that the sheets will catch fire. When neighbors are smokers, in any case, clothes will absorb the smell of tobacco.

We discussed how to deal with smokers in the article: “Is it possible to smoke on the balcony?”

Internal systems

The owner will receive greater confidence in the safety of things if he decides to dry them inside the balcony.

According to the method of fastening, there are four types of internal systems:

floor;
wall;
with fastening to railings;
ceiling

If you don’t want to bother with installation, you should attach clotheslines on the balcony to the railings on the inside. Sometimes a similar structure is attached to the window sill overlooking the loggia. The system may contain a supporting part made of ropes or metal crossbars.

Wall systems

Such structures are easy to install; you don’t even have to stand on a ladder. Folding dryers are commonly used to save space. The installation process is a little simpler than that of ceiling models.

Sliding

A plastic block is attached to one of the walls. It should be located at such a height that it is convenient for the housewife to hang things. Then the strings are pulled out and secured on the opposite wall inside the second block. This block is removable; if necessary, it can be dismantled to tighten sagging ropes on the balcony or replace it with new ones.

In some models, the strings are tightened using a roller adjuster.

Wall-mounted inertial systems

The difference from the previous version is that, due to an internal mechanism, the clothes lines on the balcony or loggia are automatically tensioned. Inside the body there is a drum with springs that tensions the strings.

If the cords begin to sag, the drum rotates and tightens them. Therefore, the strings do not sag, even if heavy things are regularly hung on them. The fastening for the inertial system is a special bar or hook.

When all things are dry, the case can be dismantled so that it does not clutter up the free space.

Cantilever or folding

The most compact ones have a folding design reminiscent of scissors. Suitable even for cramped balconies and cluttered with furniture. When folded, this dryer resembles a small bar. It is made of aluminum with a protective coating, less often - of wood.

If there is not enough space, then the structure is not fully expanded. When the structure is folded, it is almost invisible. Advanced models are produced with an electric drive, due to which the crossbars are lowered and raised with one click.

Electrically powered devices may have the following additional functions:

built-in humidity level sensor;
hair dryer;
disinfection function;
backlight

Ceiling system Liana

The dryer is a structure made of hollow metal tubes through which strong cords are threaded. The tubes are located parallel to each other. The operating principle of the system resembles an elevator. If you need to hang laundry, just pull the string and the bar will lower. Next, you can place wet things on the crossbar and lift it back up.

The structure rests under the ceiling, but things can be reached at any time without standing on a stool. This is important for older people and pregnant women. The height is easy to adjust, and a long coat can be placed so that it does not touch the floor. The housewife has the ability to pull out the crossbars so that they are at different levels. In this case, the laundry is dried more evenly.

The dryer is selected according to its length, which is usually a maximum of 2 meters. It is attached to the ceiling using fixing containers and blocks.

Clothes lines for the balcony have gone through a long evolution - from a simple stretched cord to a professional drying system with several levels. One such dryer is Liana, whose arrangement of its elements resembles a tropical forest with trees in several tiers.

Read more in the article: “Liana for drying clothes on the balcony“

Ceiling suspension system

A hook is attached to the ceiling, from which two ropes go. They support a rectangular or round frame with bars. The rungs are often positioned like steps on a ladder. Some models are coated with a coating that repels dirt. More expensive models are equipped with a built-in hair dryer and lighting.

The round drying rack is reminiscent of a children's carousel, which is hung above a baby's bed. It is advantageous to hang the ceiling system on a loggia covered with clapboard. Installation is possible using a regular screwdriver; there is no need to hammer into a concrete wall. Another example of successful installation of a suspension system is high balconies, as in Stalin buildings or the newest residential complexes.

How to install a dryer yourself was discussed in detail in the article “How to hang a clothes dryer from the ceiling on the balcony.”

Floor dryers

If at the moment it is not possible to install a permanent structure, a portable floor structure will do. When assembled, the structure takes up virtually no space. Even the simplest modifications are equipped with many crossbars and hooks that allow you to dry a large amount of clothing.

To make clothes dry faster, you should buy a floor-standing model with an electric dryer.

The disadvantage of such a device is its high power consumption.

Various internal rope attachments

Lines for drying clothes on the balcony allow you to dry clothes without taking them outside the premises. Sometimes this method of arrangement is considered the only possible one - for example, if we are talking about a French balcony. Moreover, there are many options for internal designs - and these can be homemade or factory-made devices .

The simplest type of internal structure is considered to be a fastening of two metal corners on opposite walls. Holes are made in the corners through which ropes are threaded and pulled. Metal corners can be easily replaced with wooden beams, and hooks are installed instead of holes.

Please note that for such a design it is important to choose the right height - after all, standing on a stool every time you have to hang laundry is not very convenient.

By the way, factory wall mounts are much more convenient to use - all the design details are thought out in such mechanisms, so you don’t have to invent anything during installation. The kit of such devices includes both ropes and devices for fastening them, as well as the actual wall fasteners. All this must be supplemented with instructions that allow installation to be carried out at maximum speed.

When choosing a factory device, be guided by the maximum permissible load of the design you like.

If you choose a factory system with metal “threads,” then it is better to give preference to stainless steel rather than aluminum. Firstly, aluminum is not overly resistant and stable under high loads, and secondly, it can oxidize from moisture, leaving dark spots on clean laundry.

There are two popular types of design:

Inertial. With a housing fixed to one of the walls. Inside the case there is a drum with a rope. When the laundry is hung, the rope is pulled out of the body and secured with a special hook on the opposite wall. After drying, the threads are also easy to remove. The device is quite reliable, but over time the ropes will still begin to sag. The inertial dryer can withstand a load of approximately up to six kilograms, depending on the model.
Console. They can be fixed to any part of the free surface. Such devices operate on the “accordion” principle and are easily unfolded/folded if necessary. There are both wall and ceiling structures. Ceiling ones “use up” space very economically, but when choosing them, the length of the slats and the minimum possible height of the positions must be taken into account. Cantilever dryers are fixed on one side only, extend up to half a meter and can withstand loads of up to 10 kg. The most reliable dryers are made of thick metal with a special anti-corrosion coating.

How to make a self-tightening knot on a bracelet?

There may be several options. The simplest one is if there is already a loop of rope or fishing line at one end of the bracelet. They do this because it is difficult to work with one hand without outside help. In this case, a massive decorative knot is knitted at the other end.

It should be of such a size that it can fit right through the hole in the loop. The knot is tied with the expectation that when “fastening” it, the strap will need to be slightly tightened. After threading it through the eye, the force will weaken, but the loop will not be able to come off on its own.

To prevent a self-tightening knot for a bracelet from accidentally coming undone, the easiest way is to use the scheme described above. The free end is threaded through the eyelet, turned in the opposite direction, placed under the main ribbon and passed into the resulting loop. You can also use the variants of the circuits shown in the photographs above for these purposes.