Layout on plastic windows: decorative false frames, frames, types, photos and installation

The layout for a double-glazed window is a pattern made with a profile inside or outside the double-glazed window to decorate the window or strengthen it.

Windows that are too wide and tall need reinforcement, for example, when glazing to the floor. As a rule, they lose strength due to the large surface area. But most often, layouts are used to decorate the exterior and interior of residential premises in private cottages.

A decorative layout in a double-glazed window, repeating the line of the window arch, depicting the rays of the rising sun, will emphasize and complement the overall style of the architectural design.

In some cases, several intersecting frames are decoratively depicted so that the wide window does not contrast too much with the background of the light walls.

Decorative sprats for windows are:

constructive;
invoices;
interglazed.

Decks for windows, or in other words, the layouts can be two-color, for example, the outside is lighter, the inside is darker, or vice versa.

Exquisite style in the decor of plastic windows

Beautiful window decor will help highlight the beauty of any home and make it stand out from other homes. The eyes of any residential building, setting the tone for the entire structure, are the windows. To prevent them from being dull, empty and inconspicuous, various methods of decorating them are used. A correctly chosen element that complements the beauty of the window can serve not only as a simple decoration, but also increase the strength of the windows, increasing their resistance to external mechanical influences and climatic conditions. Today there are various types of decor for double-glazed windows, which are external and internal. The main ones include:

metal or plastic sprats;
layout installed inside the glass unit;
false bindings glued to the outer surface of the glass;
hinge covers for various window fittings.

TYPES OF LAYOUTS

Windows with layout

there are two types:

· sprats (installed in a double-glazed window);

· false bindings (they are attached to the outside of the double-glazed window).

Layouts can be smooth or curved and can be mounted at different angles. Plastic windows with layouts

which are made from a special profile look really very stylish and modern.

There is a huge selection of colors and shapes on the market that will suit any style of the facade of your home.

VENETIAN SPROSES

Light slats are glued to the window structure using tape. This is how Venetian layouts are obtained, which can be easily dismantled if necessary.

Shprosy

may have different colors that can be matched to your window profile. These decorative elements do not affect the insulation of the window at all and perform only a decorative function.

VIENNA SPROSES

Checkers for windows

, which are installed on the window structure from the outside are called Viennese. Externally, they have seals, and inside there is a special frame that visually divides the glass unit into parts.

Also, Viennese patterns extend beyond the boundaries of the glass by 5 - 10 mm, which is why dust and moisture remain on them. Therefore, they should be washed carefully quite often.

CONSTRUCTIVE SUPPORTS

Large plastic windows can often be installed in private homes. This allows the designer to come up with unique layout patterns for them. False binding for plastic windows

will give the house a pleasant aesthetic appearance and emphasize the features of the facade of the house. They can also even strengthen the window structure.

Such windows have their own characteristics: such designs are quite expensive and can hold back a large amount of dust and precipitation. Therefore, if you want to order them, you must be prepared for high costs and constant care for them.

Types of sprats

The modern market for plastic windows offers various types of frames:

according to form;
width;
geometry of weave direction.

Thus, the customer can, without much difficulty, completely transform the appearance of the window by equipping it with arched or straight bars, carved in the form of various geometric shapes, circles, stars, etc.

The location of the crossbars also does not provide for any restrictions on the direction of the sectors, the location of which may be symmetrical or not. Separating strips applied to the window allow you to give the product a finished look

, harmoniously complementing its design.

The use of spraters used to be rather a necessity due to the high cost of glass. Installation of decorative overlays into the frame was carried out in small parts. The development of modern technologies has eliminated the need for window frames, however, their use is still in demand when arranging housing or non-residential premises with plastic windows if their dimensions exceed standard ones.

Decor options

Due to the heaviness of the structure of large windows, they need to be further strengthened. To strengthen the glass, its elements must be cut out and reinserted individually, thereby reducing the overall load during operation.

Window frames can be made of wood, metal, plastic, and the width is selected at the discretion of the customer.

The price of a structure with sprocket bars depends, first of all, on the massiveness of the product and its width.

From a design point of view, attics equipped with windows with decorative shutters look original. Stylish curtains or the production of original blinds will help complete the process of complete transformation.

With due diligence and knowledge of the intricacies of the process, every homeowner will be able to equip a window with sprocket bars without the involvement of craftsmen.

Double-glazed windows with spacers can be equipped with decorative elements of various sizes and shapes

Decorative overlays related to the Venetian type

, combine many varieties. In most cases, metal, polymer or wood are used for their manufacture. Double-sided tape or silicone is used to secure the binding. These materials can easily withstand aggressive environments when exposed to external influences, which allows them to be used not only for internal work, but also for fixation from the outside.

Venetian frames, also called false bindings, give a share to the imagination of customers and designers. The pattern of false frames on window structures can be changed if necessary.

The products are low in cost, and the ability to purchase a ready-made frame with easy installation in a double-glazed window makes this method of decoration accessible to most homeowners.

Decorative element close up

Sprats, classified as Viennese type
, are similar in the method of fastening to Venetian sprats. A distinctive feature is the internal placement of a special spacer frame inside the glass unit, creating an effect similar to constructive interlocking. The sealing gasket is characterized by increased reliability, and the binding width does not exceed 76 mm. The spacer protrudes no more than 12 mm above the surface of the glass unit.

The method of installing inter-glass spacers is internal, through a special hole equipped with a spacer frame. A cross-shaped connector is used to fix the plates.

Sprats, made in the form of three-dimensional patterns, give special attractiveness and respectability to the design. 8mm plates bend to create the most intricate patterns and shapes. The product is painted in bulk, with the application of a varnish coating or film. An interesting option would be to apply two-color tinting to the window.

The sprockets in the form of an overlay are connected by a frame mounted to a wooden frame. The product is fixed from the outside, without touching the surface of the glass unit. This overlay allows you to decorate the window without the risk of accumulation of dirt and dust on the glass in the places where the brackets are installed. In bad weather, dirt and raindrops calmly flow down the glass surface, making it easier for owners to maintain the glass unit.

Installing overhead shutters is not difficult, but their use is limited: if the sash is opened using a rotating or sliding mechanism, its use should be abandoned.

How do interlocking bars affect the thermal conductivity of a window?

Thermal conductivity of a window is one of the important conditions when choosing a double-glazed window.

The sprocket, which breaks the glass connection, worsens the thermal insulation qualities of the window. This is due to the low heat transfer coefficient at the junction of the glass and the window profile, where heat is lost faster.

Compared to windows without decorative weave, the thermal conductivity coefficient of decorated windows is 10-20% higher. This means that double-glazed windows with interlocking bars are cooler.

A large number of window layouts leads to high heating costs. The more layouts, the faster the double-glazed window releases heat from the room.

Overhead sprockets in the design of a country house

In windows with Viennese frames, the spacer frame inside the glass unit also reduces the thermal insulation properties. It becomes a kind of bridge that conducts the cold, which can lead to the window fogging up and freezing.

The coldest structural joints, and aluminum interglazed ones, reduce thermal insulation without touching the glazing.

Plastic windows with Venetian shrouds have virtually no effect on the thermal conductivity of the window.

Return to content

Structural sprats

They are parts of frames, each of which has a glass unit inserted into it. Their sizes can be the same or different, as well as their shape. That is, the frames are separated by them. And they have not only a decorative, but also a constructive function. Thanks to them, the structure becomes much stronger and more reliable. After all, there is an additional frame. This type of glazing is usually used for large windows. And their weight, of course, is quite large. However, such windows have a higher thermal conductivity. Therefore, they are not very common in cold regions. Structural shrouds are usually used in cases where a fairly large area needs to be glazed. Such windows are often installed in cottages, dachas, attics, etc. This allows you to make the rooms much brighter and more comfortable. And from the outside, windows of this type look much more impressive. But such sprockets are not suitable for creating patterns of unusual shapes, complex bends, etc.

What it is

Shpros and false bindings are decorative elements that are installed in window openings. These are thin or thick dividers. They perform a decorative function and create the impression of the presence of gratings. No special skills are required for installation - the strips are easily attached and removed if necessary. In 90% of cases they are made of aluminum, then painted in the desired shades. Upon request, the planks can be made from other materials.

Attention! It must be remembered that when installing these structures, there is no additional reinforcement of the double-glazed window or window opening. Planks are an additional element designed to decorate the glass or facade of a building.

Types of sprocket:

Structural sprats

Structural crossbars are part of the frame. Using such spacers, you can divide the light opening into several symmetrical or asymmetrical parts. A separate glass unit is inserted into each artificially created part. Such brackets are made from an impost profile made of the same material from which the window frame itself is made. The dimensions of the structural beams are from 56 mm to 110 mm. The color in this case, as a rule, is the same palette as the frame itself.

Inter-glass spacers

Interglazed grommets - layout in a double-glazed window using strips made of synthetic material or, more often, made of aluminum; the grommets are fixed inside the double-glazed window. Using connectors, placing the strips at different angles, you can create almost any simple pattern (star, sun, lattice, etc.). Interglazed bars are used in double-glazed windows with distances between the glasses of 8-18 mm, since they themselves have a width of 8-18 mm and even 26 mm. The only thing is that the use of wide bars does not allow bending them into an arch; wide bars are suitable for dividing into horizontal and vertical stripes.

Venetian sprats

Venetian sprats - unlike inter-glass sprats, they are glued to double-sided adhesive tape or soft silicone on the outside of the glass unit on the surface of the glass, on one or both sides. If necessary, such sprockets can be easily removed. As a rule, they are made of plastic, less often of aluminum and wood. Such sprats are rounded or trapezoidal in shape, and come in various widths from 24 mm to 40 mm, and rise above the surface of the glass to a height of 5 mm to 15 mm.

Viennese sprats

Viennese sprasses - like Venetian ones - are glued to the glass surface on the outside of the double-glazed window. The difference between them is that on the Viennese frames, a sealant is attached to the edges of the slats, similar to the sealing gaskets on the window bead; it can also be either black or gray. The second difference is the installation inside the double-glazed window of a spacer frame running parallel to the frame glued to the other side of the glass. This design creates the appearance of dividing the window into parts, and at first glance it looks as if the division was made using structural grommets, but the glass is still solid, it is all one double-glazed window, and not several as in cases using structural grommets. It is reasonable to use Viennese sprats to impart rigidity to large double-glazed windows.

Layouts (shpros) are one of the types of window decoration. The profile is glued to the glass or mounted inside the double-glazed window structure. This creates the illusion of a binding in the form of a lattice, arch and other geometric elements. All types of window layouts are divided into two main groups depending on the design: frames and false frames.

Prices for plastic windows with layout

Product cost: 9,400 rubles

Product cost: 10,830 rubles

Product cost: 11,800 rubles

Turnkey price: RUB 18,400

Turnkey price: RUB 21,770

Turnkey price: RUB 22,840

*Prices for windows with shutters are calculated taking into account the use of the Rehau Blitz profile. The price includes a volume discount.

Decorative layouts mean special elements in the form of profiles of various widths, which are mounted in double-glazed windows and visually break them into several parts. As a rule, the width of such profiles varies from 8 to 40 mm, and the colors can be very diverse.

How and why are decorative layouts used?

The main advantage of this element is its stylish and elegant design, which gives the window a special personality and attractiveness. Due to their high performance characteristics, decorative layouts are very popular today and make it possible to give the glass unit greater reliability and durability.

The palette of shades includes a rich range - from light or dark colors to golden and silver colors. It is also possible to combine various elements to create a unique geometric pattern or ornament.

This layout retains its appearance for a long time, giving the interior a special sophistication and organically fitting into a wide variety of style solutions. The traditional version involves a rectangular layout, asymmetrically breaking the glass into equal rectangles. As an original design solution, we can offer a wavy and arched layout in combination with a radial one, which creates a pattern simulating sun rays.

Decorative layouts can be of two main types:

Simple binding - frame

This blind binding, or frame, is designed to hold three panes of glass. It is made from six rectangular bars of the same cross-section. The middle bars, slabs, should be thinner. They do this. At the ends of the long bars of the harness there are eyes, in the middle there are through or blind sockets for the tenons of the horizontal bar (slab), which has spikes at the ends, and in the middle there are sockets into which the spikes of the vertical slab will go.

The top bar has spikes at the ends, the bottom bar has lugs at the ends, and in the middle there are sockets for a vertical slab. Only spikes remain at the ends of the vertical croaker.

Having filed down the spikes and eyes, they begin their further processing. The cheeks of the tenon parts are cut off and the wood is hammered into tenons and lugs or sockets. They chisel precisely along the marks and always on both sides, followed by trimming and cleaning of individual roughnesses. Having removed all the roughness, the folds are selected using a folding tape or a zenzubel.

After selecting the folds, the width of the tenons and eyes on the binding bars remains different, which complicates their assembly or connection and requires cutting off the cheeks. Therefore, it is better to make the spikes and eyes the same width by cutting off the protruding parts. To ensure that the bars and slabs are tightly adjacent to one another, the protruding part of the bar is cut off with a chisel “on the miter” at an angle of 45°.

The folds are made with a width equal to one or two tenon thicknesses. In this case, the folds pass along the edge of the tenon, which facilitates the connection of parts and does not require additional sawing and trimming.

Having prepared all the bars, we begin to assemble the binding. A groove up to 10 mm deep is planed in the lower block at the same level as the tenon. The low tide block is attached to this groove. In the figure, the upper assembly is shown from the reverse side so that the folds are better visible. The parts in the assemblies, for example the spikes in the eyes, must fit tightly against one another.

The accuracy of a dry-assembled binding must be checked.

At the same time, pay attention to the fact that the binding folds are strictly at the same level or in the same plane. Then the glass fits tightly on the folds, and less putty is required

Assembling the binding-frame: a - checking the binding for squareness with squares and a diagonal strip (shown by the dotted line), b - the procedure for assembling the binding using glue (shown in numbers 1-6), c - drilling holes for inserting dowels, d - inserting dowels, e - cutting off the spikes, e - installation of ebbs (drains) and their shape: 7 - straight, 8 - rounded

After checking the binding, mark all its parts, disassemble them and begin gluing in this sequence. First, bars 3, 4, 5 are assembled, inserted into block 1, then block 2 is inserted and strapping block 6 is put on them. The spikes and eyes are smeared with glue sequentially during assembly.

Having assembled the binding, it is placed in wedges, checked with a square and a lath for squareness, and compressed with wedges at the knots until the parts are tightly abutted. Then, in the corners, holes with a diameter of 10-12 mm are drilled with a brace or a drill, dowels are taken, dipped in glue, inserted into the holes and hammered in with a hammer. After aging, the binding is processed exactly to size and cleaned.

Having cleaned the binding, they begin to install a cast on the lower and middle bars of the outer binding. The shape of the ebbs can be different, but a semicircular or rectangular teardrop groove is always placed under them, positioned at a distance of 10 mm from the outer edge. The length of the ebb is equal to the width of the binding.

To fasten the ebb in the lower beam of the binding, at a distance of 10 mm from the fold, select a groove with a depth of up to 10 mm. The width of the groove should be equal to the thickness of the ebb, for which purpose a ridge is left in the ebb equal to the length of the lower bar or the groove made. The comb is inserted into the groove; to do this, the ebb is cut off at the ends, and then its ends are adjacent to the vertical bars of the trim. It is not recommended to saw grooves in corner joints. The ebbs are installed with waterproof glue and additionally secured with nails.

The ends of the ebb for non-opening frames and transoms are straight or cut off at an angle of 45° for opening frames, and at 60° for the narthex.

CONCLUSIONS

Windows with layout

are beginning to enjoy great popularity, which is not surprising, because they really look presentable and emphasize decorative elements.
Also, the layout on PVC windows,
especially large ones, will visually divide the window into sections and complement the facade of the house.

Order false binding

or sprats you can visit the Window Factory website. There you will find everything that may be useful for glazing modern homes and offices. Hurry up to make a profitable purchase, because there are attractive promotions on the site!

How to install a decorative layout

Plastic windows with a layout can be decorated with interglazing bars in the form of aluminum or plastic plates, or decorative overlays. Interglazed elements are laid directly at the window manufacturing stage, so they cannot be replaced in an already installed double-glazed window. There are also ready-made overhead frames that are fixed in the opening from the outside of the glass - they are more common for wooden rather than plastic windows.

Thus, decorative layouts are divided according to installation method into:

Internal in the form of a metal or plastic profile, fixed to the windows from the inside. This layout is attached to the spacer frame using special end connectors. The end latch in this design is installed in a small 3mm hole. The internal layout performs not only an aesthetic function, but also represents a structurally necessary element - especially. if we are talking about large double-glazed windows, a large-scale glazing area. Additional structural elements provide protection for the window from external damage and the effects of temperature changes, frost, and so on.
External or external decorative layouts are attached directly to the surface of the glass after the glass unit has been assembled. The result is a false binding for plastic windows, fixed to the glass with a special adhesive layer. This method can demonstrate flat, figured or relief designs - it all depends on what decorative tasks were initially set.

For self-installation, decorative plastic overlays are most often chosen. Before installing them on the glass surface, a sketch must be made - the markings are done with a pencil or marker with maximum accuracy.

If you want to create a complex ornament instead of a traditional false binding, then you should carry out the work with special care. After all, with a large number of disparate elements, it will be difficult to correctly design all their joints formed at the intersection of the binding or at the junction of the frame, glazing beads and overlays. If the joints are uneven and rough, you can forget about the decorativeness of the window opening.

Options for sketches of plastic windows with false sash

The actual work of installing the layout on the windows is done with your own hands in the following sequence:

The decorative profile is measured in accordance with the markings on the sketch and the required part is cut off with a sharp knife - so that there are no roughness or burrs at the cut site.

The cut pieces must be applied to the window without removing the protective film. This is necessary in order to once again check the size of the elements.
You need to remove the protective film from the double-sided tape located at the bottom of the cover.
The profile for creating a false binding is attached with gentle movements and light pressure.
In order to ensure the structure is tight and durable, all joints, as well as the side parts of the linings, are treated with silicone sealant. The sealant must be applied very carefully so as not to stain the glass.

If you want to turn your windows into an impeccable design masterpiece with the help of curly overlays, it is better to entrust the process of creating the layout to professionals - this way you will save yourself from unnecessary expenses on damaged material. Window decorating specialists will use the appropriate tools and complete all work very quickly.

Recommendations for selection

If you are ordering new windows for your home, then you will be faced with a difficult choice of which frames to choose. What type, what color, what layout option. It’s easier when you need to decorate already installed windows, where only Venetian trims are applicable. To select the right option, it is advisable to contact architects, if they are not already helping you with housing construction. Designers also often deal with such issues. Well, if you still decide to create a “work of construction art” yourself, special programs for designing windows using decorative frames can help you. The main rule here is that windows should not be overloaded, both visually, so as not to interfere with the free passage of sunlight into the house, and in terms of the weight of the entire structure, this can lead to a load on the floors or deformation of the window. Here are several options for drawings on windows using sprocket strips.

A successful option for using decorative sash on windows will improve the appearance of the entire house. But if the design is poorly chosen, the window can be heavily loaded and ruin the beauty of the building. Therefore, the selection of sprocket bars when ordering a window should be approached with great responsibility.

Viennese sprats

Another type of sprats are Viennese designs. Their outer part is similar to Venetian frames, and inside the glass unit there are frames that visually divide the plastic window into smaller fragments. The thermal conductivity of such windows is slightly higher, and the ability to collect dust and dirt is at the same level as that of Venetian structures.

When installing large-sized plastic windows, structural fasteners are often used. Such elements not only improve the appearance of the glass unit, but also make it more durable. The plates divide the window into smaller fragments, which overall significantly strengthens the structure. Designers very often develop an individual window design that matches the overall interior of the room.

Despite the objective advantages, constructive interlocks are not without drawbacks. When installing them, the thermal conductivity of the window increases by 20 percent, which requires additional heating. The drainage of rainwater also slows down and the rate of dust accumulation on structures increases. In addition, the cost of windows with such frames is higher than that of simpler designs.

Decorating windows using sprats is solely within the competence of the owner of the premises. Wanting to give a country house individual features, designers often opt for decorative brackets of various designs. The advantages of such decoration are much greater than the disadvantages.

Leave your tips and comments below. Subscribe to the newsletter. Good luck to you and good luck to your family!

Ideally, it is better to discuss the design and design of windows with spraters with an architect: since different architectural styles have different divisions of window glass, and a specialist can offer unexpected and original options. After all, glass can be divided not only into rectangular sections of the same size, the bars can be radial, diamond-shaped, shifted to the edges of the window, and even laid out in the form of a pattern. But different designs have their own characteristics and limitations.

A variety of design solutions for windows with sprocket bars allows you to choose them for different situations. You need to think about this in advance, because “wrong” shutters can complicate the operation of a window with shutters, cause breakdowns, and even make life in the house less comfortable. Questions can only manifest themselves locally, so an employee of a window company is unlikely to be able to give comprehensive advice. Valuable information can be obtained from friends who have installed such an element, but only if their windows are the same as yours, and this rarely happens

Therefore, you need to pay attention to various details yourself.

Are there any disadvantages to windows with spraters?

In addition to the high thermal conductivity coefficient, structural and Venetian sprats are distinguished by the presence of stains after rain. Water washes away accumulated dust on the protruding slats, and also traps dirt at the junction of the weave and glass.

Structural joints do not allow you to create complex patterns and make bends with a small radius.

There are many options for how to decorate a room, and lighting is not the least important in this matter. You will learn how to install ceiling lighting with your own hands from the article https://vse-postroim-sami.ru/engineering-systems/electrician/1768_potolochnaya-podsvetka-svoimi-rukami/. It is also worth paying attention to the furniture; sometimes design elements can be very functional, for example, a soft headboard.

A large number of decorative elements can spoil the façade of a building and also reduce the light transmittance of a window.

It is better not to use grommets in double-glazed windows in areas with a high degree of low-frequency vibrations. Due to air vibration, over time, they can become loose and hit the glass, producing an unpleasant rattling sound.

Return to content

Loops

Hidden hinges

- an indispensable element of window decor. Hidden hinges are integrated into the sash rebate and are not visible. Concealed fittings can be used in any PVC windows with sashes weighing up to 100 kg. The fittings allow you to open the sash 100 degrees, providing the most unobstructed view from the window. The windows are adjustable in 3 planes, providing optimal adjustment of the window sash horizontally/vertically and pressure.

Article on the topic: Custom wooden veranda windows for summer cottages

Also, thanks to the fittings integrated into the fold of the sash, blowing in the area of the lower hinge is practically eliminated, which is often the cause of blowing when installing conventional fittings.

White loops

- a standard element of window fittings. It is the hinges that are largely responsible for pressing the sash to the frame and preventing blowing.

In addition to standard hinges that can withstand a load of up to 120 kg, reinforced hinges can be used in the window that can withstand a sash weighing up to 180 kg.

A regular sash is attached to 2 hinges. Special door hinges are used for entrance doors. Door leaves are usually attached to 3 hinges.

Colored loops

usually used in conjunction with colored handles for laminated windows. However, recently the tendency to decorate standard white plastic windows with colored fittings has become popular. In particular, the combination of a white window with silver-colored handles and hinges is very harmonious and stylish.

Possible colors of hinge overlays are white, brown, silver, matte gold, bronze.

Colored fittings will help you turn an ordinary window into an elegant and unique design element.

When are false linings needed?

In some cases, installing overlays on double-glazed windows is a recommendation, and in others a necessity. If the windows are in an old building, the windows of which overlook a noisy avenue, then when replacing such windows it is extremely important to preserve their original appearance. Often such windows have a decorative layout, so when replacing them with new plastic windows, this layout must be repeated. This is precisely the issue that false linings solve. Many layout options allow you to simulate any layout combination.

Types of sprats

according to form;
width;
geometry of weave direction.

Window frames can be made of wood, metal, plastic, and the width is selected at the discretion of the customer.

The price of a structure with sprocket bars depends, first of all, on the massiveness of the product and its width.

With due diligence and knowledge of the intricacies of the process, every homeowner will be able to equip a window with sprocket bars without the involvement of craftsmen.

Double-glazed windows with spacers can be equipped with decorative elements of various sizes and shapes

Decorative overlays belonging to the Venetian type combine many varieties. In most cases, metal, polymer or wood are used for their manufacture. Double-sided tape or silicone is used to secure the binding. These materials can easily withstand aggressive environments when exposed to external influences, which allows them to be used not only for internal work, but also for fixation from the outside.

Venetian frames, also called false bindings, give a share to the imagination of customers and designers. The pattern of false frames on window structures can be changed if necessary.

The products are low in cost, and the ability to purchase a ready-made frame with easy installation in a double-glazed window makes this method of decoration accessible to most homeowners.

Decorative element close up

Spross classified as Viennese type

The method of installing inter-glass spacers is internal, through a special hole equipped with a spacer frame. A cross-shaped connector is used to fix the plates.

Installing overhead shutters is not difficult, but their use is limited: if the sash is opened using a rotating or sliding mechanism, its use should be abandoned.

Advantages and disadvantages

If you install false sash on the windows, the design receives a number of advantages and disadvantages, which are recommended to be taken into account and taken into account when creating the interior. The advantages include a high decorative effect.

If these panels are installed, the thermal conductivity coefficient increases, which is a negative point. Also, after rain, stains remain on the glass. The cause of contamination is accumulated dust on the slats.

If constructive crossbars are chosen for installation, they will not allow you to create a complex pattern or pattern, or perform a bend. It is best to choose planks that are made of the same material as the frames. This will allow you to achieve maximum harmony and reduce heat loss.