Why is it blowing from VHS windows?
What to do? Possible causes and ways to eliminate them will be discussed here. If anything is unclear or you have additional questions about why it is blowing from the VHS window, call us! 904-30-42 — Let's discuss!
Let's help today! We guarantee a prompt approach, high quality work and affordable prices!
Why is it blowing from the window Vhs (vhs)? What to do?
By replacing old, cracked wooden windows with VHS windows, we expect warmth and comfort in our home.
We hope that drafts will disappear forever, and we will enjoy the impeccable operation of VHS windows for many, many years. But, as practice shows, in reality everything happens a little differently. Over time, cold air begins to blow from the Vhs windows. Why is it blowing from VHS windows? Because of which? What to do? How to eliminate Vhs (vhs) window blowing? Some people try to solve the problem of blowing through VHS windows using tape, foam rubber, rags, blankets and other improvised means, not knowing that the cold from VHS windows can and should be dealt with in other ways.
Anti-corrosion coating - a reason to be proud of VHS
VHS hardware – silver plated
VHS fittings undergo a thorough alkaline zinc treatment. All components are coated with an anti-corrosion silver coating. Silver plating is an environmentally friendly process that complies with European Environmental Regulations and RAL standards.
To increase corrosion resistance, all fittings are coated with a homogeneous composition.
Possible causes of Vhs (vhs) windows blowing in, and ways to eliminate them
So why do VHS windows begin to let the cold in? Let's figure it out. There are four main reasons for blowing out VHS windows:
— Subsidence of the window sash Vhs (vhs) (blowing from the window)
During operation, the fittings of the Vhs (vhs) window became “loose” (the window sash sagged: it does not fit tightly to the frame, opens poorly, closes poorly - as if it was clinging to something, sticking) because of this, cracks appeared through which it blew. In this case, the Vhs window must be adjusted - i.e. set the correct horizontal and vertical position of the sash. To adjust the VHS window, you will need a special key. By tightening the adjusting screws with a wrench, the window sash Vhs (vhs) takes the desired position. However, we draw your attention to the fact that when adjusting the Vhs window with your own hands, you need to be doubly attentive and careful! There are often cases of clients who wanted to adjust the VHS window themselves and accidentally! the hinges were torn off!!! They had to be replaced, which is an additional expense.
Also, in the cold season, you should pay attention to what mode of operation the fittings are in. If the VHS window fittings are set to summer mode, you should switch it to winter mode. “Winter mode” ensures a greater fit of the Vhs window sash (vhs) to the frame.
— The window seal Vhs (vhs) is worn out
The VHS window seal has become unusable and needs to be replaced. You can check the condition and determine whether the seal needs replacing on your own. First you need to clean it from dirt and visually inspect it. The window seal Vhs (vhs) must be intact without visible damage and uniform in color. For the next stage of verification, you will need a regular sheet of paper. We open the Vhs (vhs) window slightly, push a sheet of paper onto the street and close the window. We are trying to pull out a sheet of paper inside. If the sheet is “dead”, then everything is in order - replacement of the seal is not required. If the sheet can be pulled out, the seal must be replaced, otherwise it will blow cold.
Different types of seals for Vhs (vhs) windows have different service lives. The more plastic components there are in the seal, the shorter its service life. Rehau and KBE rubber-epdm seals have proven themselves best. Recently, a new type of sealant, Shlegel Q-Lon, has appeared on the market and some “repairers” install ONLY it.
Our craftsmen have a very wary attitude towards Schlegel, because... More than once I had to replace a “just” installed Schlegel, which had failed, with a “classic” rubber seal. When choosing a VHS window seal, you should NOT proceed from the logic: “the thicker the better.” Installing a thicker seal can lead to other problems, for example, a loose fit of the VHS window - and no adjustment will help, the rubber simply will not allow the sash to close tightly, or the load on the VHS window fittings will increase, which will lead to its rapid failure .
Be careful when choosing a seal for your Vhs (vhs) windows, since in this market, as elsewhere, there are original sealing gum from well-known European manufacturers and analogues (Russian, Turkish, Chinese). Analogs are made similar in shape, but the dimensions do not always match. The composition and quality of such seals leave much to be desired. The seal for the Vhs (vhs) window must comply with GOST 30778-2001.
If, after adjusting and replacing the seal, the VHS (VHS) window continues to blow, you should call a VHS (VHS) window repair technician to diagnose, identify and eliminate the blowing. Again: master is different from master. There are very few good craftsmen and their work is scheduled several days in advance. As such, universal masters for repairing Vhs (vhs) windows are VERY rare. As a rule, craftsmen specialize in the repair and replacement of VHS window fittings or finishing.
An example of an incorrectly selected window seal Vhs (vhs)
The VHS window whistles. What to do?
Let's give a specific example of how the sealant for Vhs (vhs) windows was chosen incorrectly. The owner of an apartment located on Vasilievsky Island (new building, frequent strong winds due to the proximity of the Gulf of Finland) contacted us. The main complaint was that the windows whistle in high winds. Typically, windows whistle when the seal is poorly worn and due to broken internal joint sealing seams.
The owner of the apartment said that some “master” replaced the seal a little over a year ago. Our technician arrived and saw the new seal that was installed there. A little research, and now we see the label from the box of this seal. Please note, this is a groove seal for wooden windows!!! However, the “master” installed it in the VHS window!!! After standing for some time (about a year), this seal became unusable and the windows whistled. Of course, this seal was replaced with a classic rubber seal, which will last for more than 15 years. Also, our master restored the internal joining seam. The windows stopped whistling, the apartment became warm and quiet.
We repeat once again: Be careful when choosing a seal for your Vhs (vhs) windows! Don't believe the stories about "miracle seals"! There is nothing better than time-tested rubber seals from rehau, kbe and veka.
An example of “insulating” a Vhs (vhs) window or balcony door with a self-adhesive seal
What happens if you insulate a VHS window or balcony door with a self-adhesive seal? Let's give an example of what NOT to do!!!
It may seem that solving the problem of “window insulation VHS (VHS)” is easy and simple on your own by purchasing self-adhesive insulation at the nearest store. Attach it all over the Vhs (vhs) window, and think that the drafts have won!!! However, we draw your attention to the fact that this increases the load on the hinges and all fittings, which can lead to serious damage. You absolutely cannot do this!!! In this case, the presence of a self-adhesive seal not provided for by the design led to the fact that the main lock (drive, gearbox) broke and the balcony door stopped closing altogether.
— Poor quality installation (installation and finishing) of Vhs (vhs) windows
Installation (installation) of the Vhs (vhs) window must be carried out strictly in compliance with all instructions of GOST 30971-2012. The sad consequence of poor-quality installation of a VHS window is one thing – it’s cold!!! Why this happens:
Outside:
— the waterproofing of the external seam of the Vhs (vhs) window is broken (missing)
- no insulating foam under the tide
— the voids under the frame (box) are not filled
Inside:
— there are gaps under the window sill or threshold, voids (the installers saved money again)
— there is little insulating foam under the slopes
— there is no sealing of the joints between the slopes and the frame
After eliminating the deficiencies made by careless installers, the room will immediately become warmer.
— Windows “at an affordable price” — What are the consequences of savings?
Temperature changes lead to deformation of cheap plastic and cracks appear through which it blows. And here no repair work will help - the door needs to be replaced. Do not buy cheap and very cheap windows and balcony doors!!! Then you will regret it bitterly.
What to do if it blows from under the window sill (threshold) of a Vhs (vhs) window:
Inspect the installation seam under the window sill (threshold), it should be free of gaps, cracks and holes. If there are any holes, they must be sealed. How? It all depends on their size. If the gap or hole is small, then you can get by with sealant. If their size causes concern, then they must first be foamed, wait until the foam dries, cut off the excess, and then the foam must be thoroughly plastered. Sometimes, in special cases, this is not enough. You have to carefully dismantle the plastic window sill, fill up all the voids (remaining after poor-quality installation) and reinstall the window sill correctly.
How to insulate VHS windows yourself?
Who is guilty? What to do to make it warmer?
If you have recently installed VHS windows, then the warranty period is valid and you can safely go to the company that supplied you with the windows and write a quality complaint. In most cases, the company will not want any noise and will satisfy all your requirements.
It should be noted that following the recommendations for the care and maintenance of Vhs (vhs) windows significantly increases the duration of their flawless operation.
— carry out maintenance of Vhs (vhs) windows twice a year. Clean off dirt and lubricate all components of VHS windows. To lubricate the fittings of VHS windows and doors, machine oil is used, and silicone grease is used for the sealing rubber.
— at the end of the cold weather, switch the VHS window fittings to “summer” mode. Constant tight pressure can lead to faster wear of the VHS window seal.
- if the slightest malfunction occurs in the operation of the Vhs (vhs) window fittings, call a specialist. The application of excessive physical force when opening and closing a Vhs window can lead to damage to the fittings.
Have you tried all the above methods and it doesn't get better? Then, to insulate Vhs (vhs) windows, you yourself need to:
— wash the windows Vhs (vhs). Dust and dirt interfere with the operation of the fittings and worsen the veil (loss of tightness).
- Seal all cracks with sealant.
- stick a special heat-retaining film on the glass. It is easy to install and completely invisible on the VHS window.
How to care for VHS windows yourself
Even a simple ordinary soap solution will easily wash the profile of your VHS windows, or you can use degreasing detergents. But only wash the profile with a soft sponge, do not rub it with a hard surface. It is strictly forbidden to use abrasive and aggressive chemical compounds (which contain chlorine, acids, alcohol and other additives that actively destroy dirt). Even if at first glance nothing happened, after some time the color may turn from white to grayish-yellow.
The double-glazed unit in a Vhs (vhs) window is ordinary glass and needs to be washed like ordinary glass. Carefully, trying not to get detergents on the profile. It is important not to overdo it - so that the cleaning alcohol solution does not get on the rubber seal.
Caring for the metal fittings of a Vhs (vhs) window consists of annual lubrication, at least with sewing machine oil or simple machine oil or some other oil that does not contain additives.
It is recommended to clean the rubber window seal Vhs (vhs) once every six months from dirt, wash it with soapy water and lubricate it with silicone grease. This element of VHS windows plays the most important role in protecting against drafts, noise and street dust.
It is also important to regularly clean the drainage holes at the bottom of the door frame. If you regularly give VHS windows a little attention, they will last a long time and reliably!
Helpful tips and tricks:
— if the slightest malfunction occurs in the operation of Vhs (vhs) windows, it is recommended to call a Vhs (vhs) window repair specialist. It is strictly forbidden to use excessive physical force to open (close) the VHS window!
— after repair and restoration work, it is recommended to carry out service maintenance of Vhs (vhs) windows twice a year (cleaning off dirt and lubricating fittings and seals).
Based on our many years of experience, we recommend to our clients:
- Roto fittings. Due to its quality, Roto fittings have long been well established in the window market. Precise adjustment of the window pressure Vhs (vhs) ensures the absence of backlash and increases the service life of all mechanisms.
— seals for Vhs (vhs) windows with the highest performance characteristics: REHAU 952 and KBE 228. They comply with GOST 30778-2001 and will last more than 15 years.
Our best employees:
Yuri surveyor, 2 years of experience
Sergey master, 10 years experience
Oleg expert, 6 years experience
Andrey specialist, 3 years experience
Vadim engineer, 5 years experience
Free consultation for you:
Consultant:
Telegram:
WhatsApp:
E-mail: E-mail address is protected from spambots. Javascript must be enabled in your browser to view the address.
Deal with the breakdown
According to the regulations, maintenance of fittings, lubrication and adjustment is carried out at least once a year. If these conditions are met, the performance guarantee is 10 years!
Frequently asked questions about why it blows from VHS windows
We have collected here the most popular questions about why it blows from VHS windows; we recommend that you read the answers.
Question No. 1
Blowing from the window Vhs (vhs)
It's blowing from the VHS window, what should I do?
Answer:
There can be many reasons why it blows from a VHS window. Call and get a VHS window repair specialist in St. Petersburg (St. Petersburg) and the Leningrad Region.
Question No. 2
Blows from Vhs (vhs) windows from the hinge side
It's blowing from the VHS windows from the hinge side, what should I do?
Answer:
It is possible that the ventilation of windows Vhs (vhs) from the hinge side will be removed after adjustment. Perhaps, if the window is simply turning, you need to install an additional side clamp. The VHS window seal may need to be replaced.
Question #3
How much does it cost to eliminate the blowing of VHS windows in St. Petersburg (St. Petersburg) and the Leningrad Region?
Maybe it’s easier and cheaper to install new windows than to remove the ventilation from old VHS windows?
Answer:
The cost of eliminating Vhs (vhs) window blowing depends on the amount of work. The minimum price is 400 rubles - this is the adjustment of the window sash Vhs (vhs). Installing a new window is no easier or cheaper than repairing an old one.
Question #4
What materials and tools do you use to eliminate air leaks from VHS windows in St. Petersburg (St. Petersburg) and the Leningrad Region?
Do you have the materials and tools to stop blowing from my VHS windows?
Answer:
To eliminate the blowing of Vhs (vhs) windows, we use only professional materials and tools. Yes, we have tools for your VHS windows and we can make sure that it doesn’t blow out of them.
Question #5
Do you provide a guarantee for work to eliminate the blowing of Vhs (vhs) windows in St. Petersburg (St. Petersburg)?
What is your guarantee for work to eliminate VHS window leaks?
Answer:
Yes, we guarantee our work. There is a one-year warranty on work to eliminate the blowing of VHS (VHS) windows.
How to order to eliminate VHS (VHS) window blowing in St. Petersburg (St. Petersburg) inexpensively and efficiently
By calling, you can order the removal of VHS window leaks inexpensively in St. Petersburg (St. Petersburg) and the Leningrad Region. A VHS window repair technician will arrive at the specified address at a time convenient for you. Will quickly and efficiently complete all necessary work. The experience of our technicians allows us to guarantee that, with proper operation, the corrected problems will not reappear for a long time.
We employ only highly qualified professionals who will quickly identify and eliminate the cause of the malfunction. You will again be able to enjoy the flawless operation of your VHS windows.
Draw your attention to! We DO NOT have “general profile” specialists (from ceiling to floor) or migrant workers!!! Only professional masters in repairing Vhs (vhs) windows!!!
Did you find it cheaper to eliminate VHS window leaks in St. Petersburg (St. Petersburg)?
Send an offer from another company of similar quality and we will make it even cheaper. We are confident that our prices are reasonable!
Where do we get such confidence?
We do not have overdressed offices in every district of our beloved city, at every metro station, at every underground passage. There is no overstaffed staff. We do not advertise from every iron. BUT! We have over 16 years of experience, professional craftsmen and excellent cost optimization!
Our advantages
— We repair and service VHS windows of any complexity.
— Affordable prices. System of discounts, promotions.
— Urgent departure. Urgent repair of VHS windows at a time convenient for you.
- Only experienced craftsmen.
— High-quality materials and fittings.
— Guarantee for all types of work.
There will always be someone who will do it cheaper...
“Expensive and sweet, cheap and rotten”, “Free cheese comes in a mousetrap” - this works here too. Okay - it doesn't come cheap. The one who works cheaply is the one who steals spare parts from production, the one who pretends to be a master, the one who does not value his work. We work HONESTLY and WELL.
The choice is yours, remember that “The miser pays twice”!
Honest reviews from our clients
Features of mechanisms from VHS
Turkish VHS fittings are of high quality and durability - they function perfectly even after 15,000 opening and closing cycles. In production, tests are regularly carried out, for example, by stretching the upper hinges or pushing the lower ones, which allows you to check the performance of the most important elements of the system.
Constant quality control and the introduction of convenient mechanisms are the hallmarks of the VHS manufacturer, whose products already have 8 certificates in various European countries.
The range of fittings from VHS is wide and includes rotary locks, latches and latches, locks and truss systems. Such window systems are often installed in luxury new buildings and delight their owners for many years.
The metal elements are coated with an anti-corrosion compound that can withstand the harsh climate of Russia. In general, the fittings can be called universal: suitable for left- and right-handed sashes, easy to install, and provide burglary protection.
Prices for VHS window repairs and other types of work
The price for repairing Vhs (vhs) windows is from 300 rubles.
Make your own calculation of the cost of repair and maintenance of windows and doors
collapseexpand | ||
Window/door adjustment | ||
Adjusting the window sash Vhs (vhs) | 400 rub. | sash |
Adjusting the plastic balcony door | 600 rub. | door |
Adjusting the window sash on the loggia (facade glazing) | 400 rub. | sash |
Adjusting the sash of a wooden window with double glazing | 400 rub. | sash |
Adjusting the plastic entrance door | 1000 rub. | door |
Adjusting the plastic entrance door closer | 700 rub. | PC |
Alignment of window sash geometry (repacking) | 700 rub. | sash |
Aligning the geometry of the balcony door (repacking) | 900 rub. | door |
Window/door repair | ||
Repair of window sash Vhs (vhs) (bulkhead fittings) | 1000 rub. | sash |
Repair of a plastic balcony door (reassembly of fittings) | 1200 rub. | door |
Repair of façade glazing window sash (refurbishment of fittings) | 1200 rub. | sash |
Repair of a wooden window sash with double glazed windows (rebuilding fittings) | 1000 rub. | sash |
Repair of a plastic entrance door (bulkhead fittings) | 1500 rub. | door |
Replacing window/door seals | ||
Replacement of Vhs (vhs) window/door seals | from 100 rub. | p.m. |
Replacing the seal of a wooden window with double glazing | from 200 rub. | p.m. |
Replacing the façade glazing window seal | from 200 rub. | p.m. |
Replacing the seal of plastic entrance doors | 150 rub. | p.m. |
Replacement of window/door fittings | ||
Replacing the handle of a Vhs (vhs) window/balcony door | 300 rub. | pen+work |
Replacing the top hinge of a VHS window | from 1000 rub. | hinge + work (pivot window sash) |
Replacing the bottom hinge of a VHS window | from 1000 rub. | loop+work |
Replacing window scissors Vhs (vhs) | from 2000 rub. | scissors+work (tilt-and-turn sash) |
Replacing the main lock (drive, gearbox) of a window | from 2500 rub. | drive+work |
Replacing the top hinge of a plastic balcony door | from 1300 rub. | hinge+operation (pivot balcony door) |
Replacing the bottom hinge of a plastic balcony door | from 1300 rub. | loop+work |
Replacing the scissors of a plastic balcony door | from 2300 rub. | scissors + work (tilt-and-turn balcony door) |
Replacing the main lock (drive, gearbox) of a plastic balcony door | from 3000 rub. | drive+work |
Installation of clamps | from 450 rub. | PC |
Installation of lock strike plates | from 300 rub. | PC |
Replacing the hinge of a plastic entrance door | from 2300 rub. | PC |
Sealing window/door seams | ||
Sealing the internal seam of windows/doors | from 200 rub. | p.m. |
Sealing the external seam of windows/doors | from 250 rub. | p.m. |
Window/door service | ||
Converting winter/summer mode | 100 rub. | leaf/door |
Window sash service Vhs (vhs) | 600 rub. | sash |
Maintenance of plastic balcony doors | 800 rub. | door |
Maintenance of wooden window sash with double glazing | 600 rub. | sash |
Service maintenance of façade glazing window sash | 600 rub. | sash |
Maintenance of a wooden door with double glazed windows | 800 rub. | door |
Servicing of a plastic entrance door | 1200 rub. | door |
Cleaning and lubrication of fittings | 200 rub. | leaf/door |
Window/door opening limiters | ||
Installing a comb on a window/door | 300 rub. | comb+work |
Installing a comb on a façade window | 600 rub. | comb+work |
Installing a handle with a key on a window/door | from 700 rub. | pen+work |
Installing a child lock on a window | from 900 rub. | lock+work |
Installing an opening limiter with a cable | 1300 rub. | lock+work |
Installing a latch on a balcony door “smoker’s kit” | 900 rub. | latch+work |
Installation of the petal handle | from 100 rub. | pen+work |
Installing a double-sided handle on a balcony door | 2000 rub. | pen+work |
Finishing of Vhs (vhs) windows/doors | ||
Reinstallation of drainage system with foaming | from 500 rub. | PC |
Installation of drainage systems | from 1000 rub. | Job |
Installation of window sills | from 1000 rub. | Job |
Installation of slopes | from 300 rub. | m.p. |
Replacement of glass unit | ||
Replacing a single-chamber double-glazed window | 2000 rub. | sq.m. |
Replacing double-glazed windows | 2500 rub. | sq.m. |
Types of accessories
VHS produces several types of mechanisms, including:
- tilt-and-turn and rotary for structures made of plastic, wood or aluminum, suitable for ordinary windows, single or double-leaf;
- lift-and-slide for facades or large-sized doors and display cases, reliable, can withstand up to 250 kg of load;
- frame openers providing the necessary ventilation for small windows;
- window handles made of brass, plastic and aluminum, with keys, push-button locking or standard, available in various colors;
- handles for French windows, usually used for doors to terraces and balconies.
We carry out repairs of any complexity of all types of fittings. Call a specialist7 or mobile +7 (985) 76-74-777