What is tinting film for windows of a house and apartment, rules for its application

Concept

The tint film is based on a polymer that does not emit toxic substances. The material is highly elastic and durable, and is not subject to rotting or burning.

The polymer is coated with a metallized fine layer, including nickel, copper alloy, bronze, titanium and aluminum. The high-quality composition is distinguished by a multilayer structure, and a wear-resistant laminate is located between the layers. The latter is necessary to provide additional protection against accidental damage.

Manufacturers set the following material parameters :

  1. Degree of light transmission . The higher the percentage, the more transparent the finished coating becomes. It seems that it is better to choose a tint with a minimum transparency, but this will only create complete shading and the light will simply stop entering the room.
  2. UV protection . The parameter indicates the degree of penetration of ultraviolet radiation into the internal space. The maximum indicator provides protection for human health, protects against discoloration or destruction of the surface of interior items.
  3. Protection from exposure to infrared rays . Tinting with reflection of infrared radiation gives the optimal temperature in the room. This means that the heating rate of the room is significantly reduced, as a result of which you do not have to constantly use the air conditioner.

The main purpose of installing the film is to reduce the level of exposure to ultraviolet radiation. But you should not use a film that is too cheap or dark, as it will completely darken the room. As a result, only artificial lighting can be used.

When is it used?

Tint film is applied in the following cases :

However, not all rooms should be tinted. If the room is cool and the windows face north, northeast or northwest, the air will slowly warm up.

This solution is also not suitable for those who work near a window in natural light. This is especially true if the activity requires extreme visual acuity. In winter, the windows cannot be opened, so almost no sunlight penetrates.

What do you get from tinting windows in your apartment?

This method of protecting an object has many more advantages than disadvantages. Thus, they note the opportunity to reduce the cost of paying utility bills. This is due to a decrease in heat loss in winter. In summer, energy is also saved because the air conditioner does not need to be turned on regularly.

Additionally, there is an improvement in the indoor microclimate in summer: the air is heated less intensely, and a comfortable temperature is maintained longer on hot days. In addition, there is no need to constantly monitor the condition of the curtains and the operation of the air conditioner. The presence of tinting film on double-glazed windows allows you to save time by not performing these tasks.

Requirements

The technical composition affects the key requirements for finished films:

  • the polymer is used to impart an elastic composition;
  • coloring elements provide the desired degree of darkening and the required shade;
  • contact adhesive is used to securely attach the film;
  • absorbing filters are provided to protect against ultraviolet penetration;
  • laminate as a base has a high degree of adhesion to protect against film delamination;
  • The outer layer is provided for additional protection against mechanical and physical influences.

Manufacturers produce films containing different numbers of layers. Their exact number depends on the functional purpose of the composition. Thus, products with impact-resistant properties are resistant to mechanical damage. Dyed films do not include metallized components.

Features of washing and ironing

Often, complex contaminants form on the surface of a transparent silicone tablecloth, for example, dried sauce with lumps of food. They form especially often where children are present at the table and using a sponge to clean the surface does not give the required result. In this case, you can put the coating in the wash.

The properties of silicone materials allow them to be processed in automatic washing machines, but certain rules must be observed, in particular:

  1. The use of aggressive bleaches is unacceptable;
  2. Before washing, the covering will need to be folded and placed in this form in the drum of the washing machine; it should not be crumpled;
  3. When washing, you must use only the saving (gentle) mode;
  4. The washing time should not exceed a quarter of an hour, and the water temperature should not be more than 30 degrees.
  5. The use of spin and dry modes is unacceptable.
  6. It is advisable to use a special mesh for washing.
  7. It makes sense to use soft gels as a cleaning agent.
  8. It is better to remove complex stains manually in advance.


When washing, you must use only the saving (gentle) mode.

Kinds

Manufacturing conditions affect the quality and variety of the resulting film. Manufacturers produce the following models:

MirrorThey are one of the most popular and are made of metallized polyethylene terephthalate. The high-quality composition blocks up to 99% of radiation. Provides reliable protection from unwanted attention, heat and solar radiation. Among the manufacturers, we can highlight the UltraSolarBlock brand, which produces a film that costs 1,600 rubles.
Sun protectionThe key function is protection against heating due to exposure to sunlight. Fixation is carried out on windows on the south side. The film blocks up to 98% of ultraviolet radiation, including up to 95% of infrared rays. In this case, up to 75% of visible light passes through. The manufacturer STELLINE produces film that costs 351 rubles.
ProtectiveThe film has anti-burglar and anti-vandal properties. This is a good alternative to window bars, which increases the strength of the glass. Protection classes A1, A2 and A3 are provided. offers film costing 850 rubles.
MatteThe film is affordable. Decorative models are available, which can give not only the desired shade, but also a decorative design. The USB manufacturer offers the film at a price of 900 rubles.

It is important to choose not only the purpose of the film. Parameters such as density and color scheme are taken into account. Light transmittance is indicated as a percentage. The higher the parameter, the more light will pass through the film. Manufacturers offer gold and silver shades, as well as bright colors.

Why do you need to tint your car windows?

Many car owners think about the above question before tinting their windows. There are several reasons why you should tint the windows of your “iron horse”:

  • aesthetic function - tinting improves the appearance of the car;
  • masking function - a film with a low percentage of light transmittance allows you to hide the driver and passengers from prying eyes;
  • protective function - the tint film reduces the heating of the car interior, protects the driver and passengers from the scorching rays of the sun in the summer, prevents fading of the seat upholstery and delays ultraviolet rays that are harmful to humans. In addition, the film is a kind of protective layer that holds shards of small broken glass in the event of a traffic accident.

DIY tinting tools


To make a window opaque, you will need the following tools :

  • a stationery or construction knife with a sharp cutting element;
  • spray bottle with soap solution;
  • rubber spatula;
  • the required amount of tint film.

The sequence of actions when installing the film will not be the same. You will not have to take any additional steps, but it is important to follow the sequence of each step.

Caring for a Tinted Window

Glass tinted with film should not be washed during the first week after pasting, so as not to damage the coating.

In the future, when the film finally “lies” on the glass, you can care for the window as usual, avoiding only abrasive cleaning products, hard brushes and sponges.

If dirt has formed on the glass unit, there is no need to scrape it off. It is enough to moisten it with soapy water, and after a while simply remove it with a damp sponge. And then polish the surface with a soft, lint-free cloth.

( 79 votes, average: 4.90 out of 5)

    Related Posts
  • Beige color in the interior: rules for creating harmony
  • How to choose a desk for a schoolchild

How to tint correctly?

Window tinting is performed following a number of steps :

  1. Film preparation. The roll is unrolled on a flat surface, after which the material is straightened. A blank is made according to a pre-prepared template. It is important to mark the cut line with a marker. At the same time, make a margin of at least 2 cm around the perimeter.
  2. The glass is thoroughly degreased and cleaned of contaminants. Then they go over the surface using a sponge with a soap solution. Then the surface is finally cleaned using a rubber spatula. In some cases, the procedure must be repeated several times depending on the degree of contamination and the installation location.
  3. Repeated cleansing. If the film does not stick immediately after treatment, it is necessary to re-apply the soap solution.
  4. Remove the protective composition. They do it themselves. It is advisable to have an assistant involved to prevent damage or displacement of the film.
  5. The adhesive side can be additionally moistened with a soap solution from a spray bottle. This makes the gluing process easier. Such actions allow you to adjust the location of the film on the glass surface.
  6. The film begins to be glued from the top. To do this, apply a film to the edge of the glass, after which the part is completely smoothed over the surface. It is important to make sure that each section is well adhered.
  7. Using a rubber spatula, completely squeeze out air bubbles and moisture from under the film. Smoothing is done from the center towards the edges. At the final stage, the film is cut around the edges using a sharp knife. After this, you need to smooth the perimeter again using a rubber spatula.

An extremely sharp knife must be used. Otherwise, the material will tear, after which it can no longer be used for application to glass.

Types of films for window glass

Sun protection


Solar control films are most often purchased by apartment owners whose windows face south. Windows covered with such material reflect at least part of the attacking solar energy. As a result, the room heats up less on sunny days, and there is no glare on the monitors of household appliances (TVs, computers, etc.), interfering with watching programs and/or working.

Mirror

This type of glass film is especially in demand among owners and residents of apartments on the first floors. And also for those who live in houses that are close to each other.

Many people, in order to avoid outside curiosity, are forced to keep the curtains in their apartments closed around the clock. Mirror films for windows solve this problem quickly and inexpensively. After all, they guarantee a mirror (or in other words one-sided) visibility effect, when those who are inside the home see everything that is happening on the street, and those who are outside see nothing of what is happening indoors.

This film has only one drawback - it does not help in the evening or at night. Since the lighting of the apartment becomes many times brighter at night, it is no longer possible to maintain the intimacy of what is happening with only mirrored window coverings.

Protective


In principle, both sun-protection and mirror tint films have a protective function. Any such coating can protect the room outside the window from unauthorized entry, because the surface covered with it does not break well. The films have an anti-shock effect. And depending on the type of tinting used, the glass can be made completely shockproof, or an attacker will have to make a lot of effort to break it.

However, the protective option can work not only against villains. The film can also protect people (and especially children) from fragments of an accidentally broken window. In the worst case, glass trimmed with film will break into several large fragments, and in the best case, the fragments simply hang on the film, remaining on the frame.

Matte

This finish is a solution that is ideal for internal glass partitions in a residential or commercial space. With the help of these films you can cheaply and quickly improve the division of any room. They reduce transparency and make each zone in an apartment or office impenetrable and closed. In addition, matte films can protect company employees or house residents from injury in the event of the destruction of such partitions.

The economic benefits of using this type of finish are also obvious. Matte film is much cheaper than special glass with a similar visual and practical effect.

Errors in the process

It is important to pay attention to each stage of film tinting, since errors can lead to disruption of the evenness of the coating. As a result, the decorative and functional properties of the new surface are reduced.

If you choose the wrong material, its abilities are reduced . It will not save valuables from thieves or provide complete protection from direct exposure to sunlight. So, you should not choose decorative film instead of protective film, since they have different percentages of light transmission and darkening coefficient.

It is important to cut the material correctly. It is worth remembering to increase the material by 2 cm. If this is not done, some areas of the window may remain untreated. And this will reduce the success of the entire event.

The work should be carried out by two people. This will prevent the appearance of defects or tears in the fabric. The connection will be made correctly.

It is advisable to buy material with a margin of 5-10%. This will protect against reduction in the amount of materials due to incorrect calculations or damage during operation.

Preparation and tools to tint your car

We've sorted out the laws, chosen the film, and now we can get to work. You immediately need to choose a suitable place for the upcoming manipulations. The street is not very suitable for this. Dust, insects, wind and direct sunlight are the main list of unacceptable conditions. A spacious garage or box is ideal.

To ensure that the execution process does not stop “at the most interesting place,” prepare all the tools and materials in advance. You will need:

  1. The tint film itself is in the required quantity. Decide how many glasses you will tint and calculate the area. Allow a margin of 10–20% for adjustment.
  2. Water spray in any form. Needed for spraying soap solution.
  3. Liquid soap or Fairy, clean water.
  4. Something sharp and cutting: an ordinary blade, a stationery knife, a scalpel.
  5. Lint-free wipes.
  6. Forcing is a special spatula with which you will remove the solution from under the film. Should be firm, but without sharp edges. They are usually plastic and some manufacturers include them with film. If you are unlucky, then look for them in construction or automotive stores; they are also definitely available in stores for outdoor advertising specialists.
  7. Special scraper for cleaning windows (optional, greatly facilitates the cleaning process).
  8. Electric hair dryer with temperature controller (we need 550 degrees Celsius).

Everything you need to do it yourself (photo)

Spray gun Fairy Construction hairdryer Scraper for cleaning windows Film Stationery knife Forcing Lint-free napkins

Pros and cons of use

of tinting using film can be highlighted


  1. Creating dimming sunlight. The maximum effect is achieved on windows facing sunny sides. As a result, the illumination is reduced, but sufficient light remains.

  2. Protection from strangers. This effect is achieved by installing a mirror film. The armored surface will protect against penetration into the premises.
  3. Increased security. Even if the glass breaks, the fragments will remain on the surface of the film and will not fly apart.
  4. High quality decor. Film becomes an effective and cheap method of decoration. You can also apply a drawing or pattern to the surface, which is made using photo printing.

There are also some negative points. If the film is installed on the windows in the autumn-winter period, the room will slowly warm up. This reduces light transmittance. This material should not be chosen for areas that are already shaded by neighboring buildings and tall trees.

Instructions for self-tinting

To save a little on window tinting, you can do the work yourself. There is nothing complicated about this, and the tools that are needed for the job can probably be found in every home.

So, for work you will need to prepare:

  • tint film;
  • window cleaner;
  • spray;
  • microfiber cloth;
  • stationery knife;
  • plastic or rubber spatula (the second option would be preferable).

Having prepared everything you need, you can start gluing the glass on the balcony.


On some resources you can find information that tinting can be done both outside and inside the room. This is not entirely true. The film that is glued from the inside will last much longer, since it is not exposed to snow, rain, and is easier to care for.

Before covering windows, it is very important to thoroughly clean the glass. To clean the canvas from dirt and dust, you can use a robot vacuum cleaner for windows. Then use window cleaner, alcohol or a special product to degrease the surface.

Make sure that there is not the slightest trace of dirt left on the glass. After all, even the slightest lint or speck of dust, once under the film, can cause bubbles or peeling.

At the next stage, you need to measure the visible part of the glass and cut out a piece of glass of the required size from the film. This can be done in advance; even before cleaning the glass, prepare blanks of the required size. This will save you some time.

Next, you need to spray the surface of the glass with water from a spray bottle, remove part of the film from the protective layer and carefully apply it to one of the upper corners of the glass.

Carefully glue the film to the glass using a spatula or towel. Bubbles may appear during work; they will need to be smoothed out immediately with a spatula. Try to carefully smooth out every millimeter of the film - its service life will depend on this.


During work, it is important to monitor the air temperature in the room. So, you should not carry out work in rooms where the air temperature exceeds +35 °C, or less than +10 ºС

When all the film is pasted, check if there are any protruding edges beyond the edge of the glass. If there are any, they can be carefully trimmed using a stationery knife.

When gluing glass, you need to monitor the humidity level in the room where the work is being carried out. Too dry/humid air can cause poor adhesion of the film to the glass, which will consequently negatively affect its service life.

Average prices for services

It is important not only to choose the right film, but also to install it correctly. This is not always easy to do on your own. The craftsmen will complete the work in a short time, eliminating the possibility of mistakes.

The cost of installation is from 950 rubles per square meter when installed on a surface of more than 25 square meters. m. If the area is smaller, the calculation is performed individually, since much depends on the parameters and design features, as well as the cost of visiting the site.

Law and punishment for installing inappropriate tint

To avoid having to remove only the pasted tint at the first traffic police post, you should take into account the permissible standards. According to the law, or more precisely GOST 5727–88, the windshield must transmit at least 75% of the light, and the front side windows - 70%. A dark stripe is allowed on the windshield, but not more than 14 cm from the top edge. There are no restrictions on rear windows. The only thing is that deep tinting (less than 5%) requires the installation of rear-view mirrors on both sides (i.e., possible on all modern cars).


The percentage of light transmittance you choose depends on your goals and applicable regulations.

The penalty for non-compliance with these standards is not very large - 500 rubles. Since the spring of 2015, “frightening” information has been circulating on the Internet about a new law, which provides for a threefold increase in the amount of the fine (with a repeat of 5,000 rubles). At the beginning of autumn 2016, the law had not been adopted.

Thanks to installers, the service of installing reusable tinting has become quite popular. Like, if you were caught with a removable film, then nothing will happen. But reality shows the opposite. In 95% of cases, the court takes the side of the traffic police, arguing that at the time the vehicle was stopped, the offense had already occurred, and therefore, you may well be fined.

How to protect windows from bright light

During the hot summer, many people need to protect their apartment from high temperatures that rise due to the sun's rays.

The thing is that clean glass, when sunlight passes through it, can create a sufficiently high temperature. To avoid such troubles, you can install a tinting film as an option. Specialists from tonirovka24.com.ua can perform high-quality tinting of windows and office partitions.

Today, stores offer a large selection of films that can be selected according to their qualities and characteristics. There are darkening films, mirror films, multi-colored ones, everything opens up the opportunity for you to choose what you need.

Creating optimal conditions with the help of tinting film is not difficult and all the work can be done before the end of the day. If a specialist gets down to business, then very soon everything will be done in the best possible way.

Types of film coating

Currently, many categories of canvas have been developed, which are conventionally divided into types:

  • Stained glass film on glass. It is used to form ornaments on glass window surfaces;
  • Athermal material. Protects the room from infrared rays;
  • Self-adhesive stained glass film on glass with a pattern. The most popular canvas among a number of similar products;
  • Protective self-adhesive stained glass film for glass. It is used not only to create stained glass windows, but also to protect various window elements from cracks and mechanical damage.
  • Statistical stained glass film. It is usually sold in rolls with a web width of 90 cm. The material does not have an adhesive base and is held on the surface due to statistical adhesion.

The different properties and quality of stained glass film on glass allow it to be used in many options, after which both the appearance and the service life of these windows are significantly improved.

To change the decoration of a window, different methods of applying patterned material to glass are used. Moreover, if we consider the self-adhesive stained glass film on windows, then it has a decorative pattern on one side, and the corresponding glue is applied on the back surface. Adhesive composition, protected from accidental touch or dust by a paper covering with glossy embossing.

Tinting of front windows and windshield according to GOST. Athermal tinting.

We produce car tinting in Moscow using films from well-known American and Korean brands. Tinting of front windows according to GOST is permitted tinting. As a rule, athermal windshield tinting and athermal tinting of front windows is the most common type of service. The light transmission of front windows with installed athermal films meets the requirements. You can also use conventional tinting films with a light transmittance of at least 75% to tint front windows and windshields. About 5% of the light is blocked by the glass itself.

Advantages and disadvantages

Silicone film has a number of advantages that distinguish it from other types of tinting:

  • Resistant to UV rays. Over the years, the product does not fade and does not lose its original appearance;
  • Resistance to temperature changes;
  • Increasing the mechanical strength of the glass surface;
  • Preservation of characteristics and shape in case of private withdrawal. If the product is dropped or dented, its shape does not change;
  • Increased impact resistance of glass;
  • Reducing the temperature inside the vehicle due to effective screening of the sun's rays;
  • Protection of interior elements (coverings on seats, dashboard and others) from fading;
  • Effective dimming without compromising visibility. After applying silicone tint, visibility for the driver remains at a high level;
  • Elimination of dazzle from other cars moving towards or in the same direction;
  • Clear fixation on the glass surface. Over time, the material does not come off;
  • Quick application. The installation process takes 20-30 seconds, and dismantling is even faster.
  • Affordable price.

Silicone tint provides a one-way visibility effect, which guarantees sun protection and increases privacy. This material can be used many times and not worry about losing its effectiveness.

POPULAR WITH READERS: Tread height of new tires, what it should be

In addition to the already mentioned advantages, it is worth highlighting the long service life, the ability to attach to any glass surface and ease of use.

The product is not afraid of high temperatures, and its application does not require the involvement of specialists - all work is carried out independently. A significant advantage is the ability to quickly withdraw money, which is especially important when traveling abroad frequently.

It is known that when traveling to another country you have to deal with the issue of tinting. If silicone film is installed on the glass, there are no difficulties with dismantling and subsequent application.

Despite a number of positive characteristics, silicone tinting has negative features.

As a rule, they concern goods from little-known manufacturers, focusing on the volume of products produced, rather than on their quality. As a result, the characteristics and parameters leave much to be desired.

Even if we exclude this aspect, the product in question has a number of disadvantages:

  • After installation on the glass, a slight distortion occurs, which almost does not affect the overall perception of the picture;
  • If installed incorrectly, the static film does not adhere well to the glass and may peel off. As a result, the risk of an accident or other emergency situation on the road increases;
  • The corners of the product are the worst to fix, as dust and dirt often get into them. An important role is played by the static effect, which contributes to the accumulation of dust;
  • Before being used in cars, silicone film was used in non-residential premises (it was for these purposes that it was produced). For this reason, the product does not have a layer that would protect the surface from scratches and other violations of the integrity of the external part;
  • Over time, the edges of the product move toward the center (shrink), leaving minor gaps along the edges of the glass. This happens because when the material is rolled into a roll at the factory onto a transparent liner (backing or protective layer), it stretches a little, and when it is released from the transparent liner before gluing, after 1-2 days the product begins to shrink. This drawback is not typical for silicone tints made on paper substrates; pay attention to this point when choosing products.

To minimize disadvantages, it is recommended to use products from trusted brands and study reviews from other car owners. With a careful approach, it is possible to avoid many negative aspects during operation.

READ ON TOPIC: What is electronic window tinting.

Pasting furniture with self-adhesive film

Pasting furniture with your own hands takes a lot of time. You need to be patient and try to carefully complete each step.

Surface and material preparation

To properly prepare the surface and the product for pasting furniture, perform the following steps:

  1. Leveling the surface. The base to be decorated must not have chips, protruding areas or cracks. Defects are covered with putty and sanded with sandpaper. Otherwise, the furniture will become covered with bubbles or will not adhere well to the base.
  2. Cleansing. Dust and other contaminants are removed from the surface. To do this, use a clean sponge and soap solution.
  3. Removing decorative elements. It is necessary to temporarily remove linings, handles, glass shelves and other parts. After gluing the film, they are returned to their place.
  4. Degreasing. At this stage, you can use special chemical compounds or simple dishwashing detergent. Wooden surfaces are treated with acrylic varnish.
  5. Open it up. Before purchasing a finishing product, create a drawing containing elements intended for gluing. This will help to correctly determine the width of the roll and eliminate the need to create a large number of joints. The joints should not have small surfaces. The sketch is applied to the wrong side of the canvas. There is a marking grid with a mesh size of 1 cm. After cutting out the parts, you can glue the self-adhesive film to the furniture.

Gluing technology

If a small area is to be treated, for example, the facade of a kitchen unit, the film can be applied using a dry method. When decorating a cabinet or other large object, the surface is first moistened with soapy water or soap. This provides the material with mobility and eliminates unevenness. This method is suitable for people performing such work for the first time. Pasting a cabinet with self-adhesive film is done as follows:

  1. The edge of the canvas is installed on the upper part of the base. The doors can be dismantled before decoration. The top layer of the film is separated from the paper base by several centimeters. The material is pressed tightly against the surface to be treated. In this case, you need to smooth the surface with a cloth, moving downwards. The lower part along with the backing should hang down.
  2. Gradually remove the top layer from the paper base, carefully smoothing the glued area. They go down in small sections, removing bubbles.
  3. Inspect the processed item. If bubbles are found, they are pierced with a needle. By pressing the film to the surface, air is removed. When smoothing, wrinkles may appear. The damaged area is heated with a hairdryer and smoothed out again.

Difficult areas

Difficulties may arise when processing corners and other difficult areas. The following tricks will help you properly cover your cabinet with self-adhesive film:

  1. You can use a hair dryer to bend the fabric. The material is heated with a stream of hot air.
  2. Difficulties may arise at the stage of comparing coverage elements. To prevent gaps from appearing, the sheets are glued with an overlap of 1.5 cm. A ruler is applied to the allowance. Using a construction knife, make an incision and remove the excess strip. The result is an even joint.
  3. You need to work in good lighting. If you paste over complex parts in a dark room, you may miss minor imperfections. They will stand out in daylight.
  4. If the film quickly adheres to the surface, use talc. The base is sprinkled with powder, after which the canvas is applied.

How to remove self-adhesive film

When the old material has already worn out or is simply tired, boring, and you want something new, you can afford to change the self-adhesive. But to do this, you need to know how to remove it correctly so as not to damage the base or the material to which it was glued.

To remove the film, you can use the following methods:

  • Exposure to hot water. Wet the surface generously, leave for 5-10 minutes and gradually slowly peel off the film. If it is a wall, you can use a knife or a sharp spatula, but you need to act carefully so as not to damage it.
  • Another option is a hair dryer. Heat the film thoroughly with a hairdryer, wait until the adhesive layer begins to gradually move away from the surface. You can even use a hair dryer to dry your hair. But more powerful is a professional construction device.
  • An alternative to a hairdryer is a fan heater operating at maximum power. It makes the material soft and allows it to peel off easily.

If there are traces of glue left on the base, you can use a solvent to remove them. You can use alcohol or gasoline.

Working on errors: bubbles, creases, stripes and dots

It's not always possible to do everything perfectly the first time. Even professionals are not immune from mistakes. Some can be fixed, but not all. Main stumbling blocks:

  1. Air bubbles. It is better to deal with them at the initial stage, before the film has dried. After completing the work, be sure to slowly inspect all the windows. If you find bubbles, get rid of them by forcing them out. When the film “sets”, you will have to first soften it using a hair dryer or clothes steamer (you can use an iron with a steam generator).
  2. Speaking of the hairdryer. Without it, you will only be able to tint cars with straight windows. You won’t be able to straighten the folds without heating (550 degrees).
  3. Creases should be avoided at any stage. Why? After them, a noticeable strip remains. Chinese films are particularly prone to such shortcomings; it is very easy for a beginner to spoil the material.
  4. If you notice a crooked gluing in the first few hours, then you can still save the material. You can simply cut off the excess. And the shortage can be compensated by moving the film; perhaps there is a reserve left on the reverse side. Warm up and remove the tint from the window. Re-spray the solution and apply as needed.
  5. Dirt getting under the film is not allowed. Pay close attention to this during the washing phase.
  6. It takes at least a day for the glue to dry completely. It is better to leave the car in the garage during this time. But if you need to drive, then do not open the windows and do not heat the interior with a stove or air conditioner.
  7. To cover all side windows, 2 square meters is enough. m of film. Together with the rear one it’s already 3 meters.

Applying tint film is a rather complicated process, but anyone can do it. The key to success is careful preparation and choosing the right material. Also, avoid rushing while working. Even a small spot can become an eyesore later, and the satisfaction from the work done will be incomplete.

Applying self-adhesive to furniture

If the part to be glued is small, for example, the facade of a cabinet, gluing is carried out on a dry surface. Larger furniture elements should be moistened with water and soapy water. In this case, there will be a chance to correct the position of the canvas if it lies unevenly. The doors, if possible, should be removed, as should the fittings.

You need to start gluing from the top. First, you should separate 8-10 cm of the film from the base and apply the sticky part to the upper area of ​​the product. Fix the area, smooth it from the center to the edges with a rag to expel all air bubbles. The lower part of the film with the unseparated substrate should hang freely. Next, you need to slowly, in parts, separate the rest of the film from the substrate and go down along the surface of the product.

If after completing the work there are still bubbles, they should be pierced with the thinnest needle, squeeze out the air, and iron the problem area. When a “wrinkle” appears, you need to blow it out with a hair dryer, then carefully smooth it out. It is also advisable to use a hairdryer to treat all corners and joints. Only after finishing the work can you return the fittings and hang the furniture doors in place.

Choosing the best film for self-window wrapping

To make the optimal choice, many parameters should be taken into account. The first is the type of film. They come in painted and metalized varieties (there are others, but inexperienced pasters should not mess with them). The second option is preferable, as it is more durable and provides good protection from sunlight, but the price is twice as high. It makes sense to take high-quality colored film for “training”. Its resource will last for 2-3 years, after which (based on the experience gained) you will decide which one to glue for the second time.

You should not take the cheapest options (most often Chinese) to learn how to tint. During installation, you will encounter additional difficulties: creases, poor glue and rapid wear. With such materials and without experience, it is unlikely that you will be able to complete the pasting process.

Recommended and trusted manufacturers (if there is a quality certificate, there may be fakes):

  • SunTek - strong adhesive, high strength and excellent thermal insulation. The Standard series is suitable for beginners.


    An example of one of the varieties of SunTek film

  • Llumar has been on the market for a long time, so the production process is mature and the quality is high. The ATR 10 LUX series has a bronze tint. The price is above average.


    Is one of the top manufacturers

  • Sun-gard - painted films from this manufacturer have a five-year warranty due to the protective silicone coating.


    Most Sun-gard films are six-layer.

  • SunControl has a “trick” in ultraviolet protection. The company is Indian, but the quality does not suffer from this. SunControl pleases with an abundance of tint coating colors
  • SolarGard uses expensive metals (copper, aluminum, titanium) in the production of its films. This gives an excellent variety of shades not available from other manufacturers (white, blue, bright green and many others). SolarGard factories are located in the USA

Choose which brand suits your liking and wallet, and we’ll get to work.

Rating
( 1 rating, average 4 out of 5 )
Did you like the article? Share with friends:
For any suggestions regarding the site: [email protected]
Для любых предложений по сайту: [email protected]