Moment liquid nails: purpose, application and proper use

This type of glue, such as liquid nails, is now very actively used in construction and repair. When performing installation, there are simply no analogues for it. In some situations, liquid nails can speed up and significantly simplify the work process. Liquid nails “Moment Installation” allow you to avoid using a hammer drill, hammers, self-tapping screws, screws and other parts in your work. It is worth considering in more detail the existing varieties of liquid nails and the main areas of their application.

Purpose

Construction adhesive “Moment Installation” is used for the following purposes:

  • for installing mirror bases on different planes;
  • for attaching PVC panels;
  • to attach shelves and decorative structures to any base;
  • for fastening tiles.

Waterproof, which allows it to be used in conditions of excessive dampness. They can be used to glue tiles or mirrors in bathrooms, showers, swimming pools, kitchens, etc.

Why are they needed?

The range of bonded surfaces is quite wide: for plastic, ceramic tiles, gypsum panels, metal, chipboard, fiberboard, OSB, foam and gas block, bricks, polyethylene, glass, Teflon, concrete and others. Allows you to connect even loosely adjacent surfaces. Some types of LG (liquid nails) can withstand loads of up to 90 kg / cm²!

Considering the relatively high cost of LG, it is irrational to replace them with simpler and less expensive adhesive compositions, but for minor repairs (tiles have fallen off, wallpaper or baseboards have come off, etc.) - it’s always just right.

Types and composition

  1. Based on synthetic polymers. Additional components are solvents of organic origin, which explains the pungent aroma. Liquid nails react with plastic and PVC, so it is not recommended to connect surfaces made of these materials. The marking on the products of this group is “MR”, it is placed on the packaging. Synthetic compounds are highly durable and resistant to moisture. Due to easy flammability, use of the product near open flame is prohibited.
  2. Acrylic based. The marking indicated on the container is “MB”. They are neutral in composition, so they are suitable for work inside the house. Usually they install baseboards, fillets or PVC tiles.

Manufacturers of products display all information about the composition, main qualities and types of materials that can be glued together on the packaging and official website.

What it is

When purchasing liquid nails, not everyone reads the instructions for use. The material is so widespread and accessible that it seems that there are no surprises to be expected from it. But this is not so, since the general name hides several solutions with different characteristics. In the original version, the glue consisted of artificial rubber with the addition of polymers.

When it first appeared, especially plastic clay, which was mined in Texas, was used as a fine filler. Since such raw materials could only be used in America, and the adhesive composition turned out to be successful, experiments began with other additives. Thanks to this, many varieties of the product appeared, but the name remained.

Instagram positive_magazin_krasok

The range of liquid nails is very wide. The general name hides several solutions with different characteristics.

  • Construction Materials

    What can be glued with liquid nails: 8 materials

Stamps

Glue Moment “Liquid Nails” is produced in 16 variations. Each has its own adhesive strength, differs in composition and is designed for a specific material.

Specifications

CharacteristicRubber basedWater based
CompoundContains toxic volatile substances that give the glue a pungent odor, so when working with it you need to carefully ventilate the room.Does not contain toxic substances, no pungent odor. Has great gripping force.
Special FeaturesMoisture resistance, frost resistance (operating temperature can reach -40 °C)Water resistance, frost resistance (up to -20 °C)
ColorFlesh color, there are white and colorless models.White, colorless after drying.
ApplicationInstallation, but can be used as a sealant.For installation indoors and outdoors.
Type of bonded materialAlmost anyone.Various materials.
Type of bonded surfacesBetter glues smooth surfaces that do not absorb moisture.The surface must absorb moisture.
Drying timeSome varieties can dry instantly. The average working time, depending on the brand, can be 10-30 minutes. It sets within a day, and liquid nails dry completely in a maximum of 7 days. The working time of the train is 5-15 minutes. When completely dry, you can paint with acrylic paints.
Operating t°C-12… +35 °C+5… +30 °C
t°C storageFrom -20 to +30 °C, fully restored after defrosting.From +5 to +30 °C
SolventWhite Spirit.Excess glue can be easily removed with a damp sponge.
Expiration date1.5-2 g.18 months
Consumption per 1m2Depends on the brand.Depends on the brand.
Release formCartridges, tubes. Weight 0.125-0.4 kg. Cartridges, tubes. Weight 0.125-0.4 kg.

How to use glue

During work, you must follow safety rules.

The principles of working with “Moment Montage” will be as follows.

  • Before starting gluing work, you need to clean the surfaces from dirt and foreign objects, sand them, then degrease them. The materials to be bonded must be at room temperature. The optimal air temperature for work is +10 °C and above. Some types of polymer adhesives can be used at subzero temperatures.
  • If the glue is in the form of a cartridge, then before use you need to cut off the protective seal and put on the cap. The end of the cap is cut at an angle of 45° to the desired diameter. Next, the cartridge is installed in the construction gun: press the locking tab, pull the rod towards you, insert the cartridge into the gun body, push the rod back until the disk stops at the bottom of the cylinder. Make several idle trigger presses until the glue starts to come out. To stop feeding, press the locking tab. This movement reduces the pressure of the compound inside the cartridge.
  • The glue is applied to one of the planes to be glued. This can be done in several ways. If uneven areas are glued, then the composition is applied pointwise. The dots have a size of 20 by 20 mm, applied every 0.2-0.3 mm. When you need to glue tiles or other materials of a small area, the glue is applied in waves, which enhances the primary adhesion. When gluing skirting boards and other narrow, long decorative elements, liquid nails are applied in a continuous strip. When the surface area is too large, a roller may be needed; it can be used to apply glue to even, smooth materials. A trowel is used to create greater surface contact and instant holding power. Using a notched trowel with a notch depth of 6 mm, the glue is evenly distributed over the material, with a distance of 2.5 cm from the edges.
  • After application, the object is pressed tightly and fixed for a quarter of an hour. In order not to hold the element with your hands, you can secure it with masking tape or special fasteners until the glue dries completely.
  • To prevent the adhesive from going beyond the joint, it can be limited by placing a toothpick on top.
  • If the excess still protrudes beyond the seam, then the acrylic composition is dissolved by ordinary water, so it can be removed with a damp cloth, and white spirit will help to dissolve synthetic-based liquid nails. Excess glue is removed from porous surfaces after drying by careful cutting.

When you need to glue materials with low moisture absorption ability:

  • the glue cannot be applied in a continuous layer, since in order to dry it needs to be in contact with air or ensure the presence of moisture;
  • sometimes you need to apply glue first, and then after 5-10 minutes. separate the elements so the solvent can evaporate. Only after this can the parts be pressed tightly and secured.

Construction adhesive can be used as a sealant for joints up to 20 mm wide. It is necessary to carefully fill all cavities and press down the side surfaces tightly.

The average consumption of the product is 0.2-0.4 kg/m. sq. Synthetic compounds are characterized by rapid flammability, so it is better not to use near fire and not to smoke while working.

It is better to carry out gluing in a respirator, since toxic fumes from synthetic nails can cause harm to health.

Unused composition should be stored in a closed condition. Empty containers of liquid nails are disposed of as household waste. Do not allow any glue residue to enter the drain.

Instructions for using liquid nails

First of all, you need to clean the surface that you are going to glue and degrease it. Then apply liquid nails to this surface. To do this, use a special gun. The glue can be applied in dots, in a snake pattern, or in the form of a grid.

Press the two surfaces that need to be glued together very firmly. Give them the most correct position and hold it for several minutes. Two or three minutes will be enough. Then wait about 24 hours for the glue to dry completely. At the end of this time, you can begin to carry out mechanical impact on the surface.

Tips for beginners

  • It is better to use a construction gun to apply the product. It can later be used to work with sealant.
  • If work is carried out on newly constructed concrete walls, then it is better to postpone this for at least a month to allow the surface to dry and the concrete to set. If you intend to glue PVC panels to painted walls, they must first be sanded. If the surface does not absorb moisture well, then it is better not to use acrylic nails or to prime the surface first.
  • To increase the adhesive properties of polystyrene foam, it is first coated with wood glue, which is diluted 1 to 1 with water. After drying, you can begin to apply the glue.

Complete curing of the composition requires from 12 to 24 hours; during this time it is not recommended to load the glued surfaces, so as not to reduce the quality of the gluing.

Rating
( 2 ratings, average 4.5 out of 5 )
Did you like the article? Share with friends:
For any suggestions regarding the site: [email protected]
Для любых предложений по сайту: [email protected]