Reliable German fittings from the Siegenia Aubi concern are installed inside our windows. Modern fittings of the 21st century (as opposed to fittings of the “latch” type) simultaneously lock the window along the entire perimeter! This is done with a slight turn of just one knob. Also, the fittings can tilt the sash for ventilation, saving modern residents of apartments and houses from all sorts of antediluvian vents. This not only makes life easier, more convenient and more enjoyable, but also visually increases the light opening and the amount of light entering through the window.
Microlift*
A microlift is two metal rollers in the lower corner of the sash (opposite the upper hinge), which take on the entire shock load when closing the sash and smoothly, gently roll the sash, providing incredible comfort to the user and an even longer service life of the entire product!
Feel the difference, open different windows (at friends’ houses, at work), pay attention to the sound, the smoothness of the closing sashes, the ease of operating a modern window, and finally!
*In the basic configurations of Siegenia Basic, the microlift is replaced by the so-called “rolling pad”, which performs the same function.
Set of tilt-and-turn fittings Zigenia Favorite for plastic windows
If you decide to replace the rotary fittings with tilt-and-turn fittings yourself, then you need to know:
- name of the manufacturer of window fittings to purchase components (turn-and-tilt lock, corner switch, tilt-and-turn scissors, middle locks, latch, etc.);
- name of the profile and dimensions of the sash along the sash rebate - width and height, because a number of elements of window fittings depend on these values;
After you purchase the components for remodeling the window yourself, you will need to remove the decorative trim of the top hinge on the frame in the closed position of the swing window, remove the pin from the top hinge group by pressing on it from above and pulling out the pin from below, for example, with pliers. If your sash is equipped with an overhead middle clamp, you will also need to remove the decorative trim from it and unscrew the fasteners from the frame part. After this, you need to move the handle to the open position, holding the sash with your hand to avoid falling out from a gust of wind or under its own weight.
After removing the sash, you need to unscrew the window handle, place the sash on the table with the outer side up and unscrew all the elements on the sash with the exception of the lower hinge on the sash. Next, according to the installation instructions (you can find them on the Internet), screw on the fittings in a certain sequence. When installing the fittings, you will need to cut the tilt-and-turn lock and the tilt-and-turn scissors to the size of the window; this can be done by cutting with a hacksaw or an angle grinder. When screwing self-tapping screws into a PVC profile, it is advisable to set the minimum tightening force on the screwdriver to avoid turning the self-tapping screw in the profile. Self-tapping screws must be used in sizes 3.9x25 or 4x25. When installing fittings on the sash, make sure that all fitting elements are in their middle (central) position, because The performance of the fittings will depend on this.
After hanging the sash on the frame, you need to screw the mating parts onto the frame. When the handle is turned from the middle position to the closed position, the trunnions on the fittings move: for the right sash - clockwise (view from the inside), for the left sash - counterclockwise (also viewed from the inside). We mark on the sash with a pencil the position of the trunnion in the closed position (all trunnions), then close the sash and transfer the marks to the frame, now it will be clear where to screw the strikers.
Remember that there should not be excessive force on the handle when locking the sash, otherwise the fittings will quickly fail or the window handle itself will break. If a large force is observed, then it is necessary to adjust the pressure (usually on the trunnions themselves) by turning the eccentric with a 4 mm hexagon wrench, with pliers in the case of flat trunnions, or, if the manufacturer has provided for this, with a regular figured screwdriver.
ATTENTION! Kits are NOT sent to the regions by Russian Post. Only transport (100% payment) or to SDEK pick-up points after prepayment.
When ordering, please indicate in the comments the size of the sash along the rebate and the name of the PVC profile. The product is supplied to order, upon prepayment, the delivery time is communicated individually in a response letter to the order, which must be confirmed. We recommend purchasing this product only if you are confident that you can handle the installation of fittings yourself, you have experience in such work, or the opportunity to get practical advice from friends or acquaintances.
The kit includes all the necessary locks, corner switches, scissors, strikers, a set of hinges and linings for them.
Features and benefits of Sigenia Aubi fittings:
- The reliability of Siegenia-Aubi fittings is 20% higher than all known requirements
- The kit comes with hinges designed for 130 kg, and not 100 kg (as with most well-known manufacturers).
- Setting the sash tilt to a smaller angle for winter and a larger angle for summer
- Slot ventilation 7 mm
- Safe ventilation around the entire perimeter of the window
- Availability of sash microlift for heavy sashes (except Siegenia Basic)
- Anti-burglary protection
- Winter/summer clamps
- Wear-resistant hinges
- Highest level of anti-corrosion protection
- Finally, simply aesthetic pleasure from the titanium-silver coating!
Production and installation of Rehau windows, glazing and covering of balconies
Fittings Siegenia
Siegenia fittings are known for their highest quality. The company produces fittings for windows, doors and sliding structures. This is probably the only window fittings in St. Petersburg that are still produced in Germany. In the catalog of components for windows of the Pravda Okon company, Zigenia fittings are presented in two types: basic fittings for PVC windows Favorit Classic and anti-burglary fittings for Titan AF windows .
Siegenia Favorit Classic
Zigenia Favorite served as the basis for GOST 30777-2001, which already speaks of quality. As a basic option, Siegenia Favorit Classic is designed for tilt-and-turn and rectangular sashes weighing no more than 100 kg. As a rule, Siegenia Favorit fittings are installed where a high-quality, inexpensive window of small size and standard shape is needed.
What makes such fittings for metal-plastic windows stand out?
- polymer-based locking plates ensure smooth operation of the fittings;
- window fittings for cylindrical plastic windows allow you to set large pressure adjustment ranges;
- minimal likelihood of blowing due to the groove for the seal in the top hinge;
- the use of high-quality materials increases the service life of Siegenia Favorit fittings.
Fittings Siegenia Titan AF
Zigenia Titan fittings are, perhaps, the best that window production in St. Petersburg has to offer. Let's highlight the main advantages.
- Sound insulation and heat preservation. The Siegenia Titan fittings have 7 locking points, which ensures maximum tightness of the sash to the frame, eliminating the possibility of blowing.
- Smooth handle movement thanks to polymer inserts. Window management without additional effort.
- Zigenia Titan is equipped with three ventilation mode options. Targeted micro-ventilation opens the windows a few millimeters, which is especially convenient in the cold season. Stepped ventilation allows you to adjust a convenient level by tilting the doors at a distance from the frame to 18 mm. Siegenia Titan AF also provides a winter-summer version: for summer the angle of inclination of the sash is greater, for winter it is less.
- Fittings for plastic windows with an erroneous action safety device reduce the likelihood of situations when the handle turns while the sash is not tightly pressed and the window jams.
- A special lifter holds the sash during closing, which prevents sagging. No sash sagging - no drafts.
- Burglar-resistant fittings for plastic windows prevent the sash from being pressed out and lifted thanks to high-strength steel. Siegenia Titan provides burglary protection on the ground floor.
- Siegenia window fittings help the window not to slam shut during a sharp gust of wind. The special design of the upper loop is responsible for this.
Titan Series
This series presents one of the first systems that makes it possible to install window fittings on blanks from profile structures before directly welding the sashes. In practice, this means increased installation flexibility, since the fittings are not associated with one working area. The use of roller journals also increases the reliability of the operating actions of the main mechanisms. There is also room for manual installation of elements without the use of special tools. In particular, fittings for Siegenia windows in the form of corner hinges and a fault lock are integrated into the system through simple joining. At the same time, the quality and accuracy of installation is controlled by the system itself - deviation from the standard during installation is technically impossible.
Negative reviews
It should be noted that the higher the quality and operational capabilities of engineering structures, the higher their cost. The same applies to products from a German manufacturer. Even in the entry-level segment, Siegenia fittings, reviews of which also emphasize high quality, cost 20-30% more than standard solutions from competing companies. Perhaps this is the main drawback of the product, since there are no significant complaints about the work.
SIEGENIA TITAN AF
Tilt&Turn
1 | TKEB0020-002010 | Decorative trim EB RAL9003 (white) |
2 | TKEO0010-002011 | Decorative trim EL O MB RAL9003 (white) |
3 | TKEU0010-002011 | Decorative trim EL U RAL9003 (white) |
4 | TKSL0020-002011 | Decorative trim S RAL9003 (white) |
5 | TKWB0010-002011 | Decorative trim W KF RAL9003 (white) |
6 | TBEB6130-100010 | Mortise hinge KF D6*16/20 D5 TS (EB) (lower without adjustment) |
7 | TBEL6110-100010 | Bottom hinge support with pin KF D3*3/3 TS up to 100 kg |
8 | TBSL6110-100010 | Scissor hinge support KF D3*3 DH TS 100 kg |
9 | TBWB6050-100010 | Scissor hinge DH KF 12/20-13 |
10 | TBSB6020-100012 | Scissor hinge support pin |
11 | TEUL2420-100012 | Extension corner BS/K3 type2+ 1RS (1200-2360) |
12 | TEUL4010-100010 | Angular transmission AF VSO 1RS |
13 | TEUL5010-100050 | Angular transmission AF VSU/K+ FH 1S |
14 | FRKA0540-100010 | Locking and tilting support S-ES FH A2860 REHAU |
15 | TGMK4050-10001 | Drive p/o 15 AF type 120 1RS (T) (1201-1600) |
16 | TSKK2010-10001 | Scissors AF type 1 (451-680) |
17 | TRSM0060-100010 | Locking plate S 56 A1900 REHAU (13) |
Rotary
1 | TKEB0020-002010 | Decorative trim EB RAL9003 (white) |
2 | TKEO0010-002011 | Decorative trim EL O MB RAL9003 (white) |
3 | TKEU0010-002011 | Decorative trim EL U RAL9003 (white) |
4 | TKSL0020-002011 | Decorative trim S RAL9003 (white) |
5 | TKWB0010-002011 | Decorative trim W KF RAL9003 (white) |
6 | TBEB6130-100010 | Mortise hinge KF D6*16/20 D5 TS (EB) (lower without adjustment) |
7 | TBEL6110-100010 | Bottom hinge support with pin KF D3*3/3 TS up to 100 kg |
8 | TBSL6110-100010 | Scissor hinge support KF D3*3 DH TS 100 kg |
9 | TBWB6050-100010 | Scissor hinge DH KF 12/20-13 |
10 | TBSB6020-100012 | Scissor hinge support pin |
11 | TRSM0060-100010 | Locking plate S 56 A1900 REHAU (13) |
12 | AGMD2120-100010 | Rotary drive DF 15 AF Type 120 3RS(T) (1221-1420) |
13 | TSAD0010-100061 | Scissor frame DF (scissor bracket) |
14 | TSSD0020-100061 | Sash stays DF/MN |
A-300 series
The A-300 series is a variation of the Siegenia tilt and turn fittings. The line is based on a combination of a microlift and a blocker for improper opening of the sash, while the principle of its operation is based on the use of a locking pin with a roller mechanism. The main feature of the model range, which distinguishes it from other accessories of the brand, is the ability to adjust the windows in three planes.
Stylistically, A-300 elements are characterized by a combination of classic and modern solutions, making them ideal for equipping both private homes and commercial buildings. If desired, the systems can be supplemented with hidden hinges and anti-burglary mechanisms.
SIEGENIA CLASSIC-FAVORIT
Tilt&Turn
1 | FBEL0130-100010 | Bottom hinge support without pin KF D3*3 TS |
2 | TBLB0010-100010 | Bottom hinge support pin Si-Line>TITAN D6 mm (d/FBEL0130)) |
3 | 707616 | Scissor hinge support KF D 3*3 DH |
4 | TBEB6180-100010 | Plastic mortise hinge KF-D6X12/12 FA |
5 | 707456 | Scissor hinge KF-12/20-13 DH |
6 | 704196 | Scissor hinge support pin D6 |
7 | FKSL0010-002010 | Decorative cover S RAL9003 (white) scissor hinge support 100 kg |
8 | FKEU0010-002010 | Decorative cover EL U RAL9003 for lower hinge support 100kg |
9 | FKEO0010-00210 | Decorative trim EL O (white) RAL9003 |
10 | FKWB0010-00210 | Decorative cover W KF RAL9003 (white) scissor hinge |
11 | TKEB0020-002010 | Decorative trim EB RAL9003 (white) |
12 | FEUL2520-100010 | Extension corner BS Gr.70 RS1 ShSF1260-1560; VSF1200-1400 |
13 | TRKV0091-100071 | Lock and release plate RIGHT A1900 |
14 | TRSM0060-100010 | Locking plate S 56 A1900 REHAU (13) |
15 | FEUL0500-100010 | Angular transmission FAV VSO 1V TS (analogous to FEUL 0230) |
16 | FEKB1010-10010 | Locking and tilting device (FHH 430-2330); FEKB1010 for FH |
17 | FSKK2010-100010 | Scissors 7 FAV type 30 (290-570) (analogue 707302) |
18 | FGMK4050-100010 | Drive p/o 15 FAV GR.120 1RS(O) (1200-1600) L=1320mm |
Rotary
1 | FBEL0130-100010 | Bottom hinge support without pin KF D3*3 TS |
2 | TBLB0010-100010 | Bottom hinge support pin Si-Line>TITAN D6 mm (d/FBEL0130)) |
3 | 707616 | Scissor hinge support KF D 3*3 DH |
4 | TBEB6180-100010 | Plastic mortise hinge KF-D6X12/12 FA |
5 | 707456/283653 | Scissor hinge KF-12/20-13 DH |
6 | 704196 | Scissor hinge support pin D6 |
7 | FKSL0010-002010 | Decorative cover S RAL9003 (white) scissor hinge support 100 kg |
8 | FKEU0010-002010 | Decorative cover EL U RAL9003 for lower hinge support 100kg |
9 | FKEO0010-002010 | Decorative trim EL O (white) RAL9003 |
10 | FKWB0010-002010 | Decorative cover W KF RAL9003 (white) scissor hinge |
11 | TKEB0020-002010 | Decorative trim EB RAL9003 (white) |
12 | TRSM0060-100010 | Locking plate S 56 A1900 REHAU (13) |
13 | 707340 | Scissors 7 DF rotary (ShSF 290-1560) |
14 | FGMD4060-100010 | Drive 15 FAV/DF Gr.120 3V TS (1201-1400) |
General information about Siegenia fittings
Metal-plastic window structures have won the trust of consumers due to many advantages. These include physical durability, insulating function, as well as an aesthetic appearance, thanks to which such systems can fit into any façade. In turn, accessories that ensure the operation of window systems made of plastic and metal remain in the shadows, although their role can be called fundamental in the structure. This is especially confirmed by Siegenia fittings, which guarantee the possibility of durable and trouble-free operation of the double-glazed window. The products represent a wide range of elements, including hinges, handles, locking mechanisms, sealing components, as well as a large selection of connecting components, linings and corners.
Most of the fittings of this brand are made of high-strength metal with an anti-corrosion coating, although there are also elements made of hard plastic, silicone and various types of rubber. At the same time, Siegenia fittings are environmentally friendly, do not emit an unpleasant odor and are fully suitable for use in residential premises.
Varieties
First of all, all models of fittings of this brand should be divided into two groups depending on the designs for which they are intended. These are window systems made of plastic, as well as combined structures that use aluminum. By the way, the first category is also suitable for use as part of wooden systems, although they are used less and less.
So, Siegenia fittings for plastic windows represent classic mechanisms, including devices for mounting on a profile that is made before the sash is formed. Such systems include the Titan complex. Perhaps the most popular system designed for basic plastic structures is the Favorit series fittings - these are tilt-and-turn mechanisms designed for the basic working configuration. Models that continue the concept of tilt-and-turn systems are also popular - for example, mechanisms with a roller locking pin.
As for the fittings intended for aluminum window structures, it is represented by models designed to ensure the operation of complex lifting and sliding systems, which also combine functionality and mechanical strength.