Stiz B sealant is used for treating balcony and window structures. A one-component paste sealant produced on the basis of acrylic latexes has high adhesive properties to polyvinyl chloride, wood, brick and plaster.
It has a resistant structure to ultraviolet radiation, as well as to natural conditions.
After vulcanization, Stiz B sealant takes on a rubber-like shape. Successfully used in construction for interior and exterior work.
Application of sealant Stiz V
Sealant Stiz V (another name is Sazilast 11) has been used for many years in construction work, including the construction of industrial and residential buildings, as well as the repair of residential buildings.
For what purposes is the sealant used:
- treatment of holes and cracks inside the building;
- sealing the junctions of window and door frames during repairs or installation work;
- Carrying out sealing of joints of interpanel elements.
The high thixotropy of the sealant (the ability of a liquid to change its viscosity under mechanical stress) becomes possible when processing surfaces in a vertical and horizontal position. This simplifies many types of installation work where conventional sealant would not do the job.
Flaws
The disadvantages of Stiz A sealant are completely offset by its advantages, but information about them is undoubtedly important to know.
The sealant does not have very high elasticity (lower than that of silicone analogues), does not have a very pleasant smell and has a porous structure after hardening. However, since the composition is used for outdoor use, the latter disadvantages are not of great importance.
Stiz A has a short shelf life: in undamaged original packaging it is no more than 6-12 months.
Main features
Among all the features of the Sazilast 11 sealant, it is worth highlighting the main ones:
- readiness of the polymer composition for use;
- it is possible to carry out surface painting or tinting of the material (independent creation of the required color of the mixture);
- ease of use;
- efficiency (there is no loss of material during operation);
- can be used for both internal and internal repair work;
- frost resistance. The sealant does not change its structure even at a temperature of –15C;
- relatively low cost.
Due to its unique properties, this sealant is considered very convenient for finishing or repair work, and the ability to paint already vulcanized sealant makes it possible to make adjustments to the design elements of the room (building) being repaired.
Specifications
Adhesion strength of Stiz B sealant:
- with concrete blocks – from 0.1 MPa;
- with PVC panels – from 0.1 MPa;
- tensile strength of the sealant – from 0.15 MPa.
A few more facts about sealant:
- the time required to form the top layer (film) is from 40 to 120 minutes;
- sealant density – approximately 1300-1400 kg/m3;
- the elastic modulus of Sazilast 11 does not exceed 0.05 MPa (subject to a deformation of 50 percent).
Review of manufacturers
The Stiz brand of mastic belongs to one of the largest manufacturers in Russia; a company called “Sazi” has divided the product by type of packaging; for more detailed information, you need to list them separately.
Plastic buckets of 3-7 kg become relevant when performing large-scale work; the average cost of goods is 560 rubles.
Folic tubes have a volume of 0.9 kg, the price is 120 rubles, but it is better to find out the exact amount directly when visiting the store. To use the tube, you need a special mounting gun; after work, the device is thoroughly cleaned.
For smaller processes, people often buy plastic containers of 0.44 kg, the price rarely exceeds 85 rubles. The model has a built-in cone dispenser, thanks to which it will be possible to economically distribute the mixture along the seam.
It is quite convenient to fill miniature gaps in walls or gaps between the window and the base, up to 1-1.5 mm. To start squeezing out the mastic, the consumer only needs to cut off the top of the nozzle, and for storage, this hole is plugged with a piece of rubber.
Recommendations for application
The uniqueness of Sazilast 11 sealant lies in the fact that it is produced completely ready for use. Its viscosity can increase at too low temperatures, so before starting repairs, it is advisable to keep the sealant in a warm building for 18 to 35 hours.
Important! It is not recommended to dilute the sealant with water, as this may change its original properties. For example, thixotropy is lost or adhesion is reduced, and as a result, the sealant will begin to crack.
Clean the surface of accumulated dust and dirt before applying sealant. Use a dry, hard cloth to remove grease and remaining cement particles. When carrying out repair work in winter, you need to clean the work surface from possible accumulation of ice or frost. It is not necessary to dry the surface before applying the sealant, since it will adhere perfectly to both wet and dry surfaces. Be sure to make sure that there are no drops of moisture on the surface.
To obtain smooth edges of the applied layer of sealant, you must first stick a strip of adhesive tape (adhesive tape) onto the seam - it will affect the width of the seam. After this, you can apply the required layer of sealant, then the tape is carefully removed.
Use a putty knife to apply a light layer of sealant to the joint portion of the panels. If a construction spatula is not at hand, take a syringe, brush or any other tool that can perform this function. The thickness of the applied layer should not be less than 3 millimeters, otherwise the desired effect may not be achieved.
Apply the sealant into the cracks of the joints carefully and evenly, without significant breaks. The width of the contacting strip of sealant applied to the surface should be in the range of 3 to 5 millimeters on both sides.
Germotex - polyurethane sealant for concrete joints (10 kg.) Krasko Germote
Shipping and payment
Germotex is a sealant for concrete expansion joints, a two-component polyurethane elastic sealant.
Seam sealant has high adhesion strength to concrete, brick, glass, rubber, wood and metal surfaces, thereby ensuring the durability of building structures and saving on repeated repairs.
Possessing excellent elasticity, Germotex seam sealant resists abrasion, puncture, rupture better than other sealing materials, i.e. satisfies the most important requirements for sealing materials for floors. The sealant has excellent adhesion (adhesion) to absolutely all building surfaces.
The elastic properties of the polyurethane system allow the use of joint sealant not only in construction, but also where sealing on flexible joints is necessary.
for sealing and sealing cracks and seams in concrete floors and slabs,
for sealing joints subject to vibration and deformation,
for repairing seams and cracks in road surfaces,
for making expansion joints in bridge structures.
Container 10kg
Attention! The label is equipped with protective elements against counterfeiting
Apply to a clean, dry surface at a temperature of outside air and the surface to be treated from +5°C to +40°C.
It is recommended to pre-prime porous cement-sand substrates with polyurethane primer PS-Grunt.
Then mix the paste (component A) with the hardener (component B) until a homogeneous mass is obtained for 3 minutes. Use the resulting composition to fill the crack with pouring or a spatula.
The pot life of the sealant is 40 minutes at a temperature of +20ºС.
The time for full strength gain is from 5 to 7 days.
Operating temperature -50ºС +60ºС.
The sealant is supplied in a container with a pre-calculated mass of paste and hardener.
Attention! The use of material in quantities other than the standard packaging is unacceptable, as this may lead to distortion of proportions and deterioration of the properties of the material. When carrying out interior work, as well as after its completion, thoroughly ventilate the room.
Use personal protective equipment
When carrying out interior work, as well as after completion, thoroughly ventilate the room. Use personal protective equipment.
Do not heat, keep away from fire.
Store the composition in a tightly closed container, protecting it from heat and direct sunlight.
Before use, after transportation at subzero temperatures, the composition is kept for 24 hours at t (20±2)°C.
Guaranteed shelf life is 6 months from the date of manufacture.
Transportation and storage
The shelf life of Stiz B sealant is no more than 6 months, provided the product is stored in undamaged packaging from the manufacturer at a temperature above -13 degrees. During transportation, when the temperature drops to -20 degrees, the sealant can be stored for 1 month (the number of freezing/defrosting cycles is 10).
How to save sealant from an open tube
Method 1. There are situations when, after completing all the work, you still have half (or more) of a tube of sealant left. It's financially stressful to throw away a good product every time. To preserve the remaining sealant, you need to remove the piston from the pipe, placing the remaining sealant in the middle of the pipe. Then lightly melt the plastic ends on both sides and press them firmly with pliers. Now you can put the sealant in a convenient place for storage. A little later, simply cut the melted side of the tube and use the sealant for its intended purpose without spending money on buying a new one.
Method 2. You can choose another, simpler method of storing sealant. To do this, you will need a regular empty jar, a lid and a seaming machine. Move the remaining sealant into an empty jar and preserve it, as grandmothers do with compotes or pickles. Try to choose the smallest jar for this so that there is little oxygen inside it in the future.
- Using a knife, cut off the threaded portion of the pipe.
- Carefully squeeze all contents into the jar.
- Remove the piston from the can if it fell there along with the sealant.
- Without wasting time, roll up the lid on the jar.
- Make sure the cap you are using is not expired and has a rubber seal.
Like all methods, this one has its pros and cons. The main advantage is that you can roll the remaining sealant into a jar in a few minutes and not worry later that the material may dry out. Moreover, the procedure is very simple.
The only downside is the need to use a syringe for further application of sealant to treat cracks and seams. But on the other hand, if you purchased the sealant for one-time use, then this storage method is justified.
Sealant for windows and glass white Germent, 280 ml
We deliver goods directly from partners from all over Russia. These products are not presented in stores and are only available for ordering on the website.
Art. 15603390 In the shopping list In the shopping list In comparison In comparison
Description
Silicone sealant for windows and glass is used for interior and exterior work and is resistant to changes in the atmosphere and temperature changes. It is used for sealing glass windows and doors, sanitary equipment. Before work, surfaces must be cleaned and degreased with acetone. The minimum width of the silicone seam is 6 mm, the maximum is 3 cm. During operation, the sealant emits a specific odor, which completely disappears after hardening. The optimal temperature for application is from 5 to 40 °C.
- profitable price;
- reliable sealing;
- resistance to temperature changes.
Characteristics
Prices and availability may vary. Please check the exact cost and availability of goods in stores.
Reviews
Sealant for windows and glass white Germent, 280 ml in Moscow
Sealant for windows and glass white Germent, 280 ml and other products in this category are available in the catalog of the Leroy Merlin online store in Moscow at low prices. Read the detailed characteristics and description, as well as reviews of this product, to make the right choice and order the product online.
Buy products such as Sealant for windows and glass white Germent, 280 ml, in the Leroy Merlin online store, having first checked their availability. You can receive the goods in Moscow in a way convenient for you; to do this, read the information about delivery and pickup.
You can always place an order and pay for it online on the official website of Leroy Merlin in Russia. For residents of the Moscow region, we not only have low prices for products such as “Sealant for windows and glass white Germent, 280 ml”, but also fast delivery to cities such as Moscow, Balashikha, Podolsk, Khimki, Korolev, Mytishchi, Lyubertsy , Krasnogorsk, Elektrostal, Kolomna, Odintsovo, Domodedovo, Serpukhov, Shchelkovo, Orekhovo-Zuevo, Ramenskoye, Dolgoprudny, Pushkino, Reutov, Sergiev Posad, Voskresensk, Lobnya, Ivanteevka, Dubna, Yegoryevsk, Chekhov, Dmitrov, Vidnoye, Stupino, Pavlovsky Posad , Naro-Fominsk, Fryazino, Lytkarino, Dzerzhinsky, Solnechnogorsk, Istra and Zhukovsky.
Tips for use
- do not allow water to get on the sealant until a surface film forms;
- NEVER dilute the sealant with water;
- try not to carry out repair work if it is snowing or raining outside;
- Upon completion of the work process, tightly close the container with the material with a special lid. This will preserve the sealant for future repairs;
- A dry cloth will help you remove any remaining product from the seams on the work surface;
- After completing the repair, wash your hands with regular soap (this will help in most cases). But if the sealant has time to harden sufficiently, then soap is no longer able to help. In this case, special chemicals are needed.
