Procedure for replacing the door handle of a metal entrance door

The security of our home largely depends on the front door. It must be durable, reliable and last for many years. But nothing works forever. And sooner or later it is necessary to replace the door handle if it breaks on the metal entrance door. Of course, you can use the services of a professional, but such repairs are quite feasible for an untrained person.

How to fix a lock if it sticks?

The method for replacing or repairing a lock will depend on its design and the type of door. The most commonly used locking mechanisms are lever or cylinder locking mechanisms. They can be returned to working condition.

Repair and replacement of cylinder lock

Work with the mechanism is carried out in the following order:

1. The first stage is to remove the locking screw located on the bar in the end part.
2. Place the key in the hole and, turning it slightly, remove the core of the lock mechanism.
3. The elements necessary for replacement are being prepared.
4. A new core is installed in the same place and secured with a locking screw.
5. After repair, check the operation of the lock.

Important The dimensions of the element inserted inside the lock must correspond to the part being replaced, otherwise replacement will be impossible.

Repair of lever locking device

Activities to repair such a lock are carried out according to a similar principle.

1. It is necessary to move the bolts, open the lock and remove the key from it.
2. The fastener located at the end of the door leaf is unscrewed. Usually it consists of several self-tapping screws.
3. The mechanism is taken out and a new one is installed in its place.
4. Now the lock body can be returned to its place and secured with self-tapping screws.
5. After repair, you need to check how well the lock opens/closes.

In some lock models, you can not change the internal components, but simply change the position of the levers. But you will have to order a new key after such recoding.

Other common problems with locking devices

1. The tongue is not fixed. The reason for this is the insufficient size of the hole made in the door frame. Then, to restore normal operation of the lock, you need to move this hole closer to the lock tongue. If the door is skewed, it will need to be adjusted more accurately.
2. The door opens with force. This happens if the lock is misaligned. Carefully inspect the door, evaluate the geometry of the door. In case of misalignment, the position of the lock will need to be adjusted.
3. The key is stuck in the lock. Relevant for metal doors. There may be two common reasons:
   Dust or debris trapped in the mechanism. To eliminate the lock, you need to disassemble, clean, and lubricate the internal parts.
4. Displacement of the internal parts of the mechanism also requires disassembling the lock, adjusting it, or replacing damaged elements.

Do-it-yourself repair of entrance doors should begin with a competent diagnosis of the problem that has arisen. Some types of breakdowns can be fixed quickly. Others will require more advanced knowledge of design features to repair.

general information

Before moving on to any actions to eliminate the consequences of a broken door handle, let's learn more about this element of the door structure.

There are several types of handles for entrance doors. The most common type is Chinese products

for two types of locks - with automatic locking and standard closing procedure. An armored cup protects such a product from damage, but the overall quality of such handles leaves much to be desired.

Handles on cylinder strips are distinguished by the correct mechanism of fastening to the door structure and the higher quality material used in their manufacture. The main manufacturer of such pens is Italy.

The next type is a lever-key version. An extremely specific type; if it breaks, you will need to determine the brand of the lock and replace it accordingly.

Designs with a separate base are distinguished by their versatility and richness of color schemes, however, this is the second category of handles, after Chinese ones, that is most susceptible to breakage. Such products often simply tear off from the door structure due to the fact that they were initially attached incorrectly, or a malfunction of the lock forces additional efforts to be made to open the doors. Also, these structures quickly lose their pleasant appearance and in this case also require replacement.

Troubleshooting

Having the necessary tools, almost all repair work can be done independently. Actions are carried out after carefully examining the damage and determining the type of problem.

Handle jamming

Metal parts wear out with constant use. Where regular friction occurs, grooves are formed. Over time, they can cling to other parts of the lock and interfere with movement. Sticking and, in some cases, even resistance to movement occurs. Often this problem can only be solved by completely replacing the mechanism.

And as a preventative measure, repairing a handle comes down to simply lubricating an iron door. In particular the elements of her castle. A little lubricant is dripped onto all moving parts including the bolt. Then you need to twist the mechanism parts in all directions so that the lubricant gets to all the necessary parts. Such a simple operation will extend the life and performance of any locking mechanism and its external parts, including the handle, for many years.

If the handle falls off

In this case, the circlip is to blame. Its deformation or displacement will weaken the grip of the handle on the guide. The ring may burst. To fix the problem, you need to get to the desired node. To do this, remove the decorative parts. You may have to unscrew hidden screws.

Having freed the node, they study the problem. If the ring comes out of its grooves, then it is installed in place. If it becomes warped or split into pieces, a new ring must be found. After repairing the unit, it is necessary to mount all parts in the reverse order.

The tetrahedron is broken

Sometimes the inner square is made of silumin. If the purchased product is inexpensive, then so be it. The use of low-quality brittle material in the swivel assembly will lead to the fact that it will quickly break if used frequently.

To fix the problem, buy a new tetrahedron, preferably steel. The locking mechanism is partially disassembled. The outer covers are removed and the handles are disconnected. The debris of the old square is removed and a new one is installed. All parts are secured in reverse order.

The tongue stopped moving

Usually the same tetrahedron is to blame. However, in this case it did not break, but was simply a little short. During installation, it was installed exactly in the middle. Then, during operation, it gradually shifted to one side and stopped clinging to the lever with one edge. The latter begins to move “idle”.

To repair a door handle, you need to purchase a new square, which will be longer than the previous one. It is possible to buy a part slightly larger than the thickness of the iron door. The excess can be sawed off. During the work, one of the handles is removed and replaced.

The handle does not return to its original position

When the lever remains lowered, the culprit is a small spring. It’s good if it just fell off and can be put back in place. If it bursts, you may have to replace the entire locking mechanism. The fact is that such a small detail rarely appears on sale.

Door handle made in China

Products from China are characterized by low-quality fittings. It is not uncommon for parts of the lever to break off. If the locking mechanism remains operational, then only the handles on the lock can be changed. To do this, new ones are purchased that match the shape and color of the entire door structure. Then the broken ones are removed, and the purchased ones are installed in their place.

Results

If you correctly determine the cause of the breakdown, then repairing the handle will take place without any problems. You just need to remember that on a metal door such parts can be right or left

This needs to be taken into account when choosing

When repairing it yourself, you must first familiarize yourself with the design of the mechanism by studying the instructions. When all the features are known, the repair can be completed successfully.

The main function of the door is to protect the entrance to an apartment, private house or country house. The door leaf is under intense influence of external factors - temperature changes, precipitation, physical activity. Such an impact can lead to failure of its structural elements. Below are the main causes of breakdowns with ways to fix them yourself. This article describes in detail how to repair the front door.

Alternate actions during substitution

There is a general rule when dismantling complex structures. You need to remember the sequence of actions, and it’s better to take pictures of everything on your phone. This will help you put everything back together correctly.

Replacing the handle begins with the sash swinging open and the key being removed from the steel door. Next, the open canvas needs to be fixed to avoid unexpected slamming. To do this, you can hammer small wood wedges under it on both sides.

To remove the swing arm itself from the guide, you need to remove the fixing bolt. The recessed part is hidden in the center, under the curve of the handle from below. You can unscrew it using a hexagon.

We begin to free the records from the screws. Unscrewing the clamping bolts, remove the linings on each side of the door one by one.

The square rod is removed and compared with the purchased one. If the new one turns out to be shorter, then it is allowed to install the old one in the space. You just need to check that the edges of the rod are intact. After this, the plates are returned to their places so that the locking mechanism can be turned.

On any side of the canvas, install one of the handles, placing it on a square. The same operation is repeated on the other side. Next they make the tie with screws. After this, the rotary arms are fixed with secret bolts.

Upon completion, you need to check the functionality. They press the handle and watch as the dog slides behind the pad. Then the lever is released and the latch is inspected to simply return to its initial position. If you lubricate the insides of the lock with machine oil during assembly, the operation of the unit will improve and its service life will be extended.

As it becomes clear from what has been written, replacing a broken door handle is not an easy operation, which an untrained person can handle. For this work, you will not need to call a service technician. Pay close attention to the choice of the newest part and be careful during the next installation.

Installing a new handle

Before you begin installing the product yourself, you need to decide where the mechanism will be installed. It must be remembered that the height from the floor should not exceed one meter; if it is higher, it will be inconvenient for a person to open the door. This figure is taken from the calculation of the average height of a person. If necessary, the height can be changed. If no significant changes in growth are observed, the device remains at the specified height. This is due to the fact that at a height of one meter it is most convenient to open doors.

Replacing the door handle

To properly install the door lever, the following instructions must be followed step by step:

• The work begins with marking. There is nothing complicated here, just decide on the height. After this, you can make markings on the door end. To make it easier to mount the product in the future, you need to mark the center with a cross. A hole will be drilled in the place marked with a cross. In the first step, it is enough to correctly mark on both sides. Thanks to the correct marking, it will be easy to carry out all subsequent actions in the future;
• The second step of the installation process is drilling the hole. It is best to use an electric drill and a feather drill. The ideal drill diameter is considered to be 22.0 mm. A 25.0mm drill bit is suitable for the side hole. To make the gap even, it is best to drill from both sides. You need to drill from the end only after the through hole on the canvas is ready;
• Now you can move on to marking the tai. A latch is applied to the door, after which a contour line is drawn on the canvas using a pencil. When the marking is made, a groove is made in the decorative strip using a chisel;
• Next is the independent installation of the mechanism. Everything is very simple. A latch must be inserted into the end hole, which is screwed on both sides with self-tapping screws. It is necessary to carry out the work carefully so that the latch does not jam and construction dust does not get into it. Using a small air pressure, all sawdust and dust are blown out of the hole.

Gorgeous front door handle

The next step is to put on a square. Everything is simple here and there shouldn’t be any difficulties. It must be inserted into the square hole of the latch; A handle is placed over the square. It is worth looking carefully at the device so that the parts have not been swapped. The set always includes a left and right handle. It is best to screw the handle to the door with self-tapping screws. It is necessary to choose the correct size of screws so that they firmly attach the mechanism to the doors; The second handle is installed according to the same principle. After installation, a check must be carried out. If everything is done correctly, there will be no difficulties in operation; At the final stage, the attachment points are masked. This is best done using decorative caps.

Required Tools

To install a handle on an interior door with your own hands, you will need the simplest carpentry tools:

• electric drill;
• crown attachment with a diameter of 50 mm;
• feather drill with a diameter of 20–25 mm;
• pencil;
• screwdriver;
• hammer;
• chisel.

To facilitate installation, a template for installing door handles, sold with the product, will help. If it is not in the package, you can print it from the Internet. The template is a 1:1 scale diagram of the mechanism body. It is applied to the canvas to mark the groove and hole. If you intend to install a large number of handles, a jig is cut out of wood for drilling.

Subtleties of self-installation of different models

If you don’t go into the design features of any specific models, then the installation of most of these devices is similar, but before we cut in this or that handle, let’s figure out where to install it.

A few words about the installation location

If we are talking about a private house or apartment, then where the handle should be installed, you have the right to decide for yourself, the main thing is that it is convenient for you and your household. But when choosing a place, experts recommend focusing on 2 things:

1. First of all, you need to measure at what height all the other handles in your house are. After all, when one handle falls out of the overall ensemble, it is very noticeable and spoils the interior;
2. If you choose a place to install all the handles in your home, then you need to focus on your arm bent at 90º at the elbow. Naturally, it is worth taking into account the height of all family members and choosing something in between.

The installation height of the door handle according to GOST is a completely different matter. The documents state that such structures are installed at a height of 1 m, plus or minus 100 mm. This information should be well remembered by office owners and business workers in administrative buildings. Otherwise, the fire inspector will have another reason to find fault.

Entrance door handle

High-quality handles on entrance doors from good manufacturers break extremely rarely; this misunderstanding mainly happens with goods from the friendly Chinese people. Fortunately, it’s easy to find a replacement in the store; the average price of such a kit fluctuates around 500 rubles.

When purchasing a new set of handles, it is advisable to remove the old trim completely and take it with you to the market.

Removing an old handle from a metal door is not difficult. In this case, it is not necessary to completely disassemble the entire mechanism; it is enough to unscrew the 2 mounting bolts that are located on the inside.

So, the handles have been purchased, now all that remains is to insert them. The inner lining has been removed, so there is practically nothing holding the outer lining in place. If you pull the handle a little harder it will come out along with the square pivot pin and connecting pins.

When buying a handle, it is better to choose models with an internal armored lining; they cost more, but the protection against burglary is much higher.

Next, screw 2 connecting pins onto the outer part of the new set of handles. Separate armor plates may be provided on the keyhole; if they fit the holes in the new set, then decide for yourself whether to change them or not.

Now we insert the square rotary pin into the core of the handle and mount the outer trim in its place. Keep in mind – the square pivot pin should almost reach the bottom of the hole on both handles. Otherwise, there is a high probability that the handles will break again.

When everything is inserted and screwed, the gasket is installed last inside the structure. Gaskets can be rubber or plastic, so try to take rubber ones, such as in the photo below.

The outer cover with the pivot pin and studs is inserted first. Then the inner lining is combined with it and all this is fixed with a pair of bolts from the inside.

Handle with latch for interior door

Often, several types of handles can be installed on a lock embedded in an interior door. This is especially true for lightweight latches; any rotary handles generally fit there. The main thing is that the turning mechanism works using a square pin.

The technique of inserting a light latch and a solid lock into an interior door is shown in detail with photos and videos “HERE”, and we will only analyze the installation of the handle.

The handle mechanism is screwed to the doors with self-tapping screws, but so that the fastening washer does not spoil the appearance, it is covered with a decorative overlay, after which the handle is installed.

In round knob handles, both the handle itself and the decorative overlay are secured using a discreet inner tongue. This tongue needs to be pushed down using the special key included in the kit. The tongue itself is equipped with a spring and after removing or installing the handle, it returns to its original position.

In rotary handles, the system is slightly different; after installing the handle, you need to fix it with a small screw on the side, and then screw it on or simply put a decorative cover on the latches (depending on the model).

The screw that secures the rotary handle can be either a Phillips screwdriver or a hexagon. In the latter case, the hexagon must come with the handle.

Features of replacing small parts

In case of replacing the spring part, the new part is strongly compressed on top, a veneer washer is placed, then a veneer ring is attached and the whole thing is connected with a screwdriver. Then the rotating mechanism is delicately screwed in, followed by inserting a spring element into it. The handle is tightened with a wrench or nut.

Sources:

• https://furni-info.ru/zamena-ruchki-dveri.html
• https://dveridoma.net/remont-dvernyx-ruchek-vxodnyx-dverej/
• https://evrostroi.by/blog/remont-dvernyh-ruchek-vhodnyh-dverej-kakie-byvayut-polomki-i-kak-ih-pochinit
• https://www.bloomhuff.com/dveri-i-vse-o-nih/8900-kak-remontiruetsya-ruchka-na-vhodnoy-dveri.html
• https://u-news.org.ua/8832-kak-pomenyat-dvernuyu-ruchku-na-vxodnoj-dveri/
• https://dver.club/materialy/zamena-metallicheskojj-dveri.html

Recommended Procedure

When planning to repair or replace door handles, you should first read the instructions to avoid common mistakes. For convenience, it is recommended to follow the standard procedure, which includes several simple steps.

Removing the locking device

You can remove a mortise lock on a metal door using a screwdriver. You will need a flathead or Phillips screwdriver depending on the type of mounting screws. The dismantling process includes the following steps:

1. Unscrew all the fastening screws that are located on the strip of the end part of the door. If a locking mechanism without a fixed cylinder is used, it is enough to pry the bar and pull out the lock.
2. Remove the screw holding the cylinder, which is the secret part of the lock. The fastening element is more elongated and passes through the entire locking mechanism.
3. Press the cylinder on either side of the door. If the part is equipped with additional protection, you need to insert the key into the lock and slowly turn it until the cylinder can be pulled out freely.

Troubleshooting and repair

A careful inspection of all parts of the door structure allows you to determine the exact faults and carry out the appropriate repairs. Most breakdowns can be fixed on your own.

The handle itself has become loose

The method for fixing the problem depends on the reason why the fittings became loose. To carry out repairs, you need:

1. Remove the handle together with the linings by unscrewing the fastening screws from the inside of the blade. If the design provides a lock, and it has become unscrewed, it is enough to return it to its original position.
2. Check the junction with the lining, where the fluoroplastic insert, retaining ring and metal washer are located. When the fluoroplastic is erased, the fastening weakens. If the stopper is deformed, the fittings also begin to wobble. In these situations, you need to replace the broken parts.
3. Inspect the part for cracks. The problem is especially common on silumin varieties. It is not possible to eliminate the cracks, so replacement is required.
4. Make sure the cylinder is functioning. If it breaks internally, you need to replace the part or the entire fittings.

Pin damage

Deformation of the pin causes the tongue of the door handle to become static and prevents the door from closing. In cheap locks, the pins are made of soft alloys and wear out quickly.

The handle falls out periodically without damaging the metal

The reasons for the handle falling out without destroying the metal blade are the weakening or breakage of the locking ring. If it is damaged, the internal components will fall out immediately after the lock is removed and the mechanism will need to be replaced. If the stopper is loose, it should be strengthened.

If the tongue does not move

When the tongue does not work when opening the door, the reason is that the inner square is not long enough. The element gradually moves closer to the latch and presses it, causing malfunction. To restore the functionality of the door handle, you need to purchase a suitable part, unscrew the fittings and replace it.

If the handle does not return to its original place

Failure to return the handle to the horizontal position occurs due to improper operation of the return spring. You can return the spring to its place by analogy with the retaining ring. If the spring has burst, it will need to be replaced. Since it can be difficult to find the right part, it is easier to change the entire mechanism.

Chinese door handle repair

Chinese fittings made of silumin wear out quickly and are not resistant to external influences. Repair of fittings is carried out according to the following algorithm:

• remove the mounting screws;
• remove the core and square of the lock;
• attach new pads;
• replace worn parts;
• return the bar to its place;
• screw the fasteners.

Some useful recommendations from experts

If the tongue is jammed, then the first step in repairing the handle of an iron door is to open it. You need to choose a suitable thin and durable item. A screwdriver works best. With its help, you need to press the tongue and push it into the lock. If this does not work, then you need to unscrew the handle on one side.

Simple tips often get rid of troubles; do not ignore them:

1. Since the mechanism contains many small parts, all repair work must be carried out carefully. The floor under the door should be covered with light-colored paper or film.
2. When purchasing a door handle, you need to consider its quality, reliability, and design. The fittings must match not only the finishing of the sash, but also the other elements.
3. We must not forget that such products are produced left-handed and right-handed. This must be taken into account when purchasing, otherwise you will have to make an exchange. It is impossible to correct this point or change the handle to the other side during installation.
4. If the device not only does not function very well, but also begins to lose its appearance, then it is better to buy new fittings. Scuffs, scratches, loss of shine or stains spoil the mood of the home and negatively affect the company's image if the handles are installed in the office.
5. When purchasing new fittings, you need to pay attention not only to its shape and size, but also to the fastening elements. Sometimes similar models have bolts that differ in length. You need to buy a suitable mount immediately or you will have to use the old one.

In the case of repair work, significant efforts must not be made. The repair scheme for a metal door handle depends on what kind of breakdown occurred. If you still have instructions for the product, you should study them. It is also helpful to watch an instructional video before attempting the repair yourself. You need to start it only with the door open, so that the door does not jam and the room does not become locked.

If you cannot repair the fittings on your own, then you should call a repairman. He will complete the work, depending on the complexity, in 20-60 minutes. When contacting a specialized company, you should describe in detail the malfunction and the handle itself; it’s good if there are instructions for it, so as to name the make and model. Such services now exist in every city, they work seven days a week.

Using a door with a broken handle is very difficult, often even impossible. Therefore, you need to try to fix it as quickly as possible, and if necessary, replace the metal door handle. Most defects are easy to fix on your own, but in some cases you need to call a specialist, especially if the handle is jammed together with the lock.

How to adjust hidden hinges?

Internal hinges are in demand because they are not visible from the outside of the room. This means that it is impossible to cut off such canopies, which significantly complicates the penetration of intruders into the house. There are several reasons for adjusting hidden awnings. This may be the formation of a gap between the canvas and the frame, rubbing of the sash, it begins to cling to the threshold.

To repair the operation of an iron entrance door, you need a hex key (4 mm). The door must be opened; this is the only way to gain access to the awnings. If the canvas has sagged down, you need to tighten the screws. If a gap begins to appear, you will have to loosen them a little. You can do this kind of work yourself, but only if you have experience in this field. But it is best to call a specialist to repair iron entrance doors.

Types of door handle malfunctions and their elimination

If you find that the door handle is broken, you must first determine the cause. Experience in using door handles allows us to identify 5 types of breakdowns that occur most often:

• The handle sticks and there is resistance when turning.
• The handle falls off, but its fastening remains in place.
• The tetrahedral pin (square) inside the lock breaks.
• When turning the handle, the tongue does not move.
• The handle does not return to its original position after turning.

Now let's look at how to repair the door handle in each of these cases.

If the handle gets stuck

The metal parts of the mechanism are subject to abrasion during constant use, especially if dust particles get there. To avoid this, you need to monitor the presence of lubricant in the lock. Drop a little oil onto the bolt and turn the handle so that it is evenly distributed over all parts.

Sometimes the reason lies in loose structural elements. It is necessary to correct their position and tighten the mounting bolts more tightly.

How to properly lubricate the door mechanism

Repair if the handle falls out

The culprit of the breakdown in this case is the retaining ring, which either becomes deformed or moves, or may even burst completely. The repair will take time, but it will not be difficult to do:

1. Remove the decorative rosette by turning it several times (sometimes it is secured with a small screw from the bottom, then you need to unscrew it first).
2. Using a screwdriver, unscrew the screws or bolts that secure the mechanism.
3. Remove the structure and check the condition of the retaining ring. If it is bent or broken (as is the case in most cases), you need to purchase a new spare part.
4. Insert the retaining ring and the entire mechanism into place.
5. Install the handle and secure it.

Removing the decorative strip and unscrewing the handle fasteners

When replacing small parts in the door handle mechanism, you need to be very careful, as this process can be hazardous.

Repair in case of breakage of the internal tetrahedral pin (square)

This is only possible when using cheap, low-quality products that are made from fragile material - silumin. In this situation, you will have to change the mechanism completely. To avoid such breakdowns, it is better to purchase steel structures from trusted manufacturers. The handle is replaced as follows:

1. The fasteners at the base of the handle are unscrewed, then the handle itself is removed.

Unscrewing the screw at the base of the handle

1. The decorative strip is unscrewed and the bolts are unscrewed, after which the entire structure is removed.
2. At the end of the door, the fasteners on the lock plate are unscrewed, after which the locking mechanism is removed.
3. The new handle with lock is installed in the reverse order.

If the tongue does not move when you turn the handle

If the latch does not work when opening the door, the cause of the malfunction is that the square is too short. It gradually moves towards the latch and presses it. As a result, she cannot function normally. In this case, you need to act like this:

1. Buy a longer square from the market. If the length is longer than necessary, you can shorten it using a grinder.
2. Unscrew one of the handles and remove the structure.
3. Replace the square and return the handle to its place.

The handle does not return to its original position

If the handle does not spring back to the horizontal position, this does not mean that it is broken - perhaps the return spring has simply slipped off. You can put it in place in the same way as the locking ring. But sometimes the spring breaks, and this becomes a problem: it is very difficult to purchase this part on the market. Often in such cases the entire mechanism is changed.

Spring responsible for returning the door handle to its original position

Repairing the handle of a metal Chinese door

Sometimes it is necessary to repair the outer metal door handle, or rather replace it, since Chinese silumin fittings often break. This is easier to do than installing a lock on a metal door. The algorithm of actions is not very different from replacing the handle of an interior door:

• The fastener is removed.
• A square is extracted. If it is the right length, you can leave it.
• Attach the pads and gaskets and install the handle on the square.
• Put the bar in place, the bolt should fall into place.
• Screw in the fasteners.

Repairing a door handle in most cases is not difficult, the main thing is to correctly determine the cause. If the structure cannot be repaired, you should think about purchasing high-quality fittings from well-known manufacturers. To more clearly imagine how to disassemble a door handle, watch the following video.

Tips for choosing hardware for your front door

In order for it to last for a long period of time, when purchasing you should pay attention to the following criteria:

• Material. It is better to give preference to models made from durable alloys of aluminum, brass, steel and other materials in accordance with personal wishes and means. It is advisable to avoid purchasing handles made of silumin, due to its fragility, which negatively affects its service life, which is often extremely short.
• Coating. Models that have been exposed with paint or varnish are susceptible to abrasion and it is better not to purchase them.
• Match the lock and handle if the structure is to be mounted on a plank.
• Price. Pens that are too cheap cannot be of high quality. In general, models with a long service life cost at least $30. When purchasing a low-quality product, you must immediately be prepared that after about a year of use a replacement will be required.

Note! If there are children living in the house, then you need to purchase handles with no sharp protrusions so that the child does not get hurt.

Eliminating squeaks

A fairly common occurrence is when a metal front door begins to creak. This sound is not only unpleasant, it indicates friction that has arisen due to improper functioning of the awnings. This means that these fittings are under extra load.

Repairing an iron door in this case is not at all difficult. To do this, you need to lubricate the parts that make an unpleasant sound. To do this, you will need a lever, such as a crowbar. With its help, the door leaf should be raised slightly. Distribute machine oil or other lubricant into the cracks near the canopy pins. After this, the canvas must be lowered to its original place. It is better to carry out the procedure together, without haste, without rushing, so that the sash does not fly off its hinges.

Cylinder door lock repair

Such restoration is carried out when replacing a well. In any stores or markets you can consult with sellers. He will easily cope with the task if the buyer brings with him old broken parts.

When making the right choice, the following must be taken into account: the dimensions and the ratio of the hole into which the screws are screwed. The insides may or may not be of good quality. If their cost is small, such a metal door can be easily broken into by selecting a key.

There are many different larvae. They can be with an internal opening or an external one. If there is only an external well, then the one in the middle will not have a hole; instead, manufacturers attach a plastic lamb. In this type of lock, the door closes from the inside without using a key.

The color scheme of the opening should match both the lock and the entrance door.