Types and methods of installing blinds on plastic windows

Modern interior design often involves installing blinds. These stylish and practical designs can become an alternative to traditional curtains or can be used in conjunction with them. Having decided to give preference to such products, it is worth understanding how they are installed. If desired, all installation work can be completed on your own.

Pleated paper blinds in the shape of a semicircle

Having decided to understand the question of how to make blinds, it is worth recognizing that one of the most inexpensive and easiest to manufacture are blinds made of paper using the pleated method.
They make it easy to refresh the interior or protect window glass during renovation work.

To make this type of curtains you will need:

Work should be performed on a flat, free surface.

Instructions on how to make pleated blinds with your own hands are as follows:

Prepare a paper strip.

Its width should exceed the dimensions of the window sash by 0.5 cm on each side. Draw strips of the required width (up to 4 cm) on the back of a sheet of paper. It should be remembered that the wider the strip, the more massive the blinds will look.

Fold the paper where the lines were drawn. If the paper is very thick, you can first use a ruler to draw sharp scissors along it so that the folds are more even.

Fold the entire strip of paper into an accordion shape and secure the edges and middle with clamps.

Measure the middle of the resulting structure and pierce it through with an awl. Insert a cord into it. Tie a knot or fasten a button in the upper part.

To make the base more rigid, glue cardboard strips to its outer slats. Thread the fasteners into the bottom of the cord. Using double-sided tape, glue the blinds to the inside of the cornice. Attach tape to the tip of the bottom edge of the blinds and make the bottom in the shape of a semicircle.

Main advantages of blinds

For their main purpose, blinds on the balcony regulate the light flux to the extent that is convenient for the homeowner. Swivel slats perform this function better than traditional sliding curtains. In the dark, blinds cover the illuminated balcony from the views of curious neighbors on the floor or from the neighboring area.

Additional benefits of blinds include:

• additional windproof layer of dense material;
• unhindered air circulation with windows slightly open;
• a large number of designs and materials, allowing you to choose curtains for non-standard glazing;
• a wide range of colors, a variety of materials (with the help of blinds they allow you to maintain the stylistic unity of the interior);
• easy care of plastic and metal structures (do not require frequent washing or dry cleaning);
• relative ease of installation of curtain rods for broaching and rotating devices.

When choosing which blinds are best for your balcony, you need to take into account the features of designs and materials.

Installation methods

Methods for installing blinds

For industrially manufactured models, do-it-yourself installation of blinds is described in the attached instructions. When independently choosing the place where the product will be mounted, all the parts (for example, brackets) are not always used.

Hanging on the opening

The desire to completely hide the window involves installing blinds over its upper part. In this case, brackets are used that will provide the gap from the blinds to the wall necessary for the free movement of the slats.

The effect of curtains is created by attaching the box (top bar) to the ceiling. There are already holes made in the cornice through which you need to screw it to the ceiling.

Before installing the blinds, mark the centers of the opening to be closed and the top of the curtain to be secured. I set aside equal distances from them for drilling holes where the fixing grips will be installed.

If you have to hang blinds with an electric drive for the movement of the slats, then you need to take into account that the dimensions of the folded package on the right and left are different, depending on the location of the motor.

Window mount

Let's consider ways to correctly install the selected curtain option without changing its performance characteristics.

It is allowed to install blinds on plastic windows using screws on the structural profile and glazing bead. Before screwing in, it is advisable to pre-drill the plastic body with a drill whose Ø is smaller than the screw thread. This will prevent the material from cracking due to excessive twisting force.

If you are installing horizontal blinds on a separate sash, then you also need to install a fixing device from below - bushings through which a tension line will be threaded to tension the fixed panel.

The manufacturer allows you to choose how to install horizontal roller blinds. The kit includes double-sided tape that firmly fixes the plastic brackets to the window profile. Below, glue holders for a fully unraveled fabric curtain to the window with your own hands.

Inter-frame installation of horizontal blinds will require drilling holes for the control mechanism in a convenient part of the transom according to the manufacturer’s diagram attached to the product. For more information about installing horizontal blinds, watch this video:

A non-damaging way to answer the question of how to hang blinds on indoor plastic windows is with special hooks hung along the top of the frame. They may be sold with the product.

The last stage of installation

The installation of horizontal blinds is completed by assembling all the elements into a functioning structure. A description of how to assemble the blinds is included with each model. Large bays on the installed cornice are inserted into the latches until they click; the drive is carried out by a cord threaded into a special fastening for the blinds, which directs the free movement forward/backward. To learn how to attach blinds to a mount without screws, watch this video:

After assembly, be sure to check how the blinds are attached by making several trial lowering and raising of the blinders. All questionable areas must be re-secured to prevent future damage.

Concept and types of blinds

Operating principle and control mechanism of blinds

How to properly measure blinds for plastic windows

Installing fasteners for blinds to the ceiling and wall

The right choice of blinds for plastic windows

Tips for choosing slats for blinds

Fastening inter-frame blinds, general recommendations

This option is suitable for double frames. Installing an inter-frame plastic curtain is a complex process and requires the need to violate the integrity of the frame profile: holes (2 pieces) are drilled to output the blinds control system (handle and cord).

They should be located at the top of the inner sash. The brackets are installed on the upper profile, using the technology for installing horizontal blinds as a basis.

Basic tips for choosing:

• Before purchasing a design, you need to clarify the composition of the kit, in particular, the presence of fasteners;
• If the installation is easy to do yourself, then it is better to entrust the repair of curtains to a specialist;
• Plastic is easier to care for;
• It is not recommended to clean the new structure too often, as this will quickly wear off the protective coating.

Installation instructions without drilling

To install it yourself, you don’t need any tools or even skills; it’s important to correctly calculate the width of the canvas and attach it evenly to the surface

For clamps

Installation on special brackets-clamps is perhaps the easiest way to hang blinds with your own hands, but this mounting option is only possible on an opening window sash:

• assemble the cornice and canvas according to the manufacturer’s instructions;
• put clamps on the cornice, check that they do not touch moving elements and do not interfere with the movement of cords and chains;
• attach the cornice to the sash, mark with a simple pencil where to hang the brackets;
• unfold the canvas, check whether it touches the protruding elements of the window; if necessary, the curtain must be adjusted to size: cut to width and shortened;
• unclip the clamps from the cornice, open the sash and put on the brackets according to the marks, make sure that they are tight and level;
• You can fasten the curtain rod and the canvas to it.

The diagram shows one of the options for hanging blinds without drilling

On tape

If you are looking for a simple and at the same time reliable way to hang blinds on a plastic window with your own hands and not damage the profile, then the option of attaching with tape is the most optimal

Here it is important to glue the cornice correctly so that the canvas hangs straight down, without distortions, otherwise there will be unsightly overlaps and gaps on the sides and bottom, in the end the blinds will quickly break

Installation steps:

• assemble the blinds according to the attached diagram;
• try it on the window, if necessary, cut it on the side and along the length, taking into account that the minimum gap between the panel and the protruding elements of the window is 5-10 mm;
• mark the extreme points of the cornice;
• draw a line between them, ideally it should be strictly parallel to the window sill;
• if the geometry of the opening is not ideal, make a plumb line from a rope and a weight, attach it to the marks, mark the side lines where the edges of the canvas will go, and straighten the line along which the cornice will be glued, it is better to have a slight distortion at the top and bottom than ugly gaps and overlaps on the sides;
• wipe the place where the cornice is fixed with solvent or acetone;
• remove the protective film from the double-sided tape and glue the cornice strictly along the line;
• check the operation of the canvas; if it catches somewhere, then it would be correct to remove the system, clean the installation site and re-glue it.

Sometimes the tape is not glued to the cornice, but the kit comes with special fasteners with a magnet or hooks. Installation of such a model occurs according to an identical scheme described above.

The video clearly demonstrates that even a child or a woman can glue blinds with tape.

Adjusting the size of blinds

Standard blinds do not always fit window openings in size, and custom-made products are much more expensive than ready-made ones. In order to save money, horizontal blinds can be cut on the sides yourself, and vertical ones can be shortened.

Cutting horizontal blinds to width and height

If horizontal blinds do not match the width or height of the opening, their size can be changed. This process is labor-intensive and requires special tools.

Since designs from different manufacturers have different sizes, sometimes it is necessary to adjust the product to a specific window. To do this, the main thing is to make the correct calculations and all manipulations must be carried out very carefully so as not to spoil the product itself.

In order to change the width of the blinds, you need to cut the slats and cornice themselves, on one or both sides at once. It is better to shorten on the side on which the control mechanism is located.

Step by step trimming process:

1. Remove the plugs and protective cover from the cornice, and move the control mechanism and cord system to the pin;
2. Place a mark on one of the slats and, folding all the slats into one multi-layer strip, clamp them with clamps or an elastic band;
3. Using a hacksaw with fine teeth, saw off the excess along the mark - cornice, lamellas and rail;
4. Finish the edges with a file or sandpaper;
5. Reassemble the structure in reverse order.

In order to change the height of horizontal blinds you need:

• Open the blinds completely and make a mark at the desired height;
• Open the bottom bar and untie the knots on the restrictive cords, then remove the clamps;
• Remove excess trims and trim the lace;
• Reassemble the structure in reverse order.

Cutting vertical blinds to height and width

In order to adjust the width of the vertical structure, you must first cut the cornice, but adhering to the basic rule - the cornice should be slightly larger than the window opening.

Step-by-step process for cutting vertical blinds:

1. In order to trim the cornice, you need to measure the required length with a tape measure and make a mark on the side on which the lifting mechanism is located;
2. Since there is an aluminum rod and cord inside the cornice, you need to remove the side cover from the cornice using a screwdriver and move the cord to the side so that it does not interfere;
3. Using a hacksaw, grinder or special file, first make a small cut so as not to damage the lace, and then cut the cornice according to the mark;
4. Remove excess hooks from the cornice, unfastening them from each other if you need to cut the top with wire cutters;
5. Shorten the cord by first unscrewing the plug that secures it and removing the end from the cord. After cutting, the plug must be put in place;
6. To cut the chain - to do this, you need to unfasten the special plastic clasp connecting its edges, take out the outermost ball and cut off the required length, and then fasten the clasp again.

When cutting vertical blinds to width, it is important not to damage the cord during the process of shortening the cornice.

In order to make the slats of vertical blinds shorter you need:

• Remove all the plates from the hooks and pull out the bar with the hook eye from each one.
• Place all the plates together, perfectly straight, and secure them with an elastic band.
• Measure the desired size and make a mark, adding 3-4 cm for the hem.
• Cut the slats using scissors.
• The edge of each strip must be treated with fire so that the fabric does not fray.
• Fold each lamella and make a hole in each for fastening.
• Insert the strip into each lamella and secure the ends with glue.

It is very important to make marks with a pencil so that each lamella is the same size, because an error of a few millimeters will create a sloppy effect.

Cutting roller blinds to width and height

To cut a roller blind to width you need:

1. Unwind the roller blind and pull out the control mechanism along with the fabric weight.
2. Make a mark at the desired height and carefully cut the fabric with scissors.
3. The length of the curtain drum should be 1 cm longer, so it needs to be cut with a margin.
4. Cut the weighting material exactly to the size of the fabric.
5. Assemble the structure.

Photo instructions for correct cutting of roller blinds to width

It is very easy to change the length of a roller blind; to do this, you just need to remove the bottom curtain rod and cut off the excess, then trim the edges of the curtain and insert the weighting material into place.

We hang aluminum curtains and blinds on sliding windows

For installation you will need a set of tools: wire, drill, Phillips screwdriver, screwdriver, drawing supplies.

The instructions for installing blinds on sliding windows contain a list of items that are carried out step by step:

Draw a marking line for installing brackets. It must take into account the distance between the clamps and the control mechanism, between the brackets (from 60 cm) and to the extreme areas on the blinds (25 cm). For large blinds and significant weight, it is recommended to use intermediate fasteners.

Drill holes for installing dowels on the surface to which you plan to attach the brackets. It is possible to use blinds on plastic windows without drilling.

Profile installation.

Fixing the top rod of the blinds on the brackets

It is important to remember that the blinds at this stage are already assembled.

Working with aluminum options on inclined surfaces requires a little more effort and skill.

Design options

Currently, according to the characteristics of their design, blinds are divided into the following types:

• Horizontal window blinds. The main feature that determines the name of this type is the horizontal lamellas (strips), assembled into a single web using a system of fishing lines.
• Vertical window blinds. A special feature of this type is the long and wide vertical slats. The size of these blinds exceeds the similar size of structures of the first type.
• Roller blinds. A solid canvas made of special fabric or bamboo fibers serves as a light filter.
• Cassette blinds. A “cassette” is a special box into which the blinds are retracted when rolled up.

Horizontal window blinds

Rice. 2. Horizontal window blinds.

Horizontal window blinds, like plastic windows, are available in various sizes. Therefore, to simplify the installation process of this structure as much as possible, careful measurements of the window dimensions (width and height) should be taken. It should be noted that in order to maintain convenience during window operation, it is advisable to install small blinds on each double-glazed window, rather than using one mechanism that covers the window completely. In the case of using large horizontal blinds that completely cover the window opening, it becomes impossible to open the sash with the slats lowered. Horizontal blinds are attached to the window frame using brackets or, in extreme cases, screws.

Vertical window blinds

Rice. 3. Vertical window blinds.

Vertical window blinds, due to the large size of the entire structure, cannot be attached to the window profile. Their base (resembling a cornice of classic curtains) is mounted on a section of the wall that is located above the window opening. In this case, it is necessary to use strong screws of the optimal size (too short ones will not work in this case). One of the disadvantages of vertical window blinds is the difficulty of opening the sashes, which can touch and cause mechanical damage to the slat system. Among the advantages are ease of maintenance and operation, pleasant external design, a wide range of materials for lamellas and a bright color palette.

Roller window blinds

Rice. 4. Roller window blinds with wall mounting.

Roller blinds for plastic windows are currently one of the simplest types of these interior elements. Small dimensions, light weight and simplified design allow the use of roller blinds on windows of almost any size.

The design of roller blinds (they are also called “roller blinds”) consists of the following elements:

• Canvas made of fabric or bamboo fiber. During production, the fabric is treated with a special impregnation liquid, which increases its dust-repellent properties. This impregnation also prevents the fabric from creasing.
• Control mechanism. This could be a chain or a spring mechanism.
• The shaft on which the fabric is wound.
• The box in which the shaft is placed. In the open type of roller blinds there is no box.

Cassette window blinds

Rice. 5. Horizontal cassette blinds with sash mounting.

A special feature of cassette blinds for plastic windows is a special cassette (or box) into which the blinds' slats are assembled when closed. The materials used for their manufacture are in most cases plastic and aluminum. Less commonly – wood and bamboo. Cassette blinds can be combined with almost any interior design style (you just need to choose a design made from a suitable material). This type is one of the most suitable for combination with plastic windows (they can be mounted directly on the window profile of each sash). The position of the slats is adjusted using a special chain.

How to properly install plastic vertical blinds

Basically, vertical blinds are mounted in front of the window opening. In this case, the most important thing is to maintain the distance from the opening to the blind mechanism. It must be sufficient so that the strips can turn without interference. The distance is determined depending on the width of the stripes.

To install blinds on windows by hand you will need:

• Dowels and screws – up to 5 pieces measuring 6.0x40 mm.
• Drill or hammer drill with a drill bit with a diameter of 6 mm.
• Screwdriver.

As a rule, blinds are sold disassembled (the cornice with the mechanism is separate from the fabric strips).

Attaching the cornice itself can be done in two ways:

• To the ceiling.
• To the wall using special brackets.

The procedure for attaching the cornice to the ceiling is as follows:

1. The first step is to mark the position of the cornice. A certain distance is removed from the wall and a mark is made on the ceiling. The same ones are applied along the entire length of the cornice in increments of no more than 1 meter.
2. A straight line is carefully drawn through the marks. You can use painter's lace for this.
3. Now, inside the cornice itself, holes with a diameter of 3.5 mm are drilled in increments of 0.5 meters. A self-tapping screw will be screwed into the dowel through them.
4. Once the holes are drilled, you can begin “trying on” the cornice. To do this, you will need the help of one more person. The cornice is applied along the line and through the holes drilled in it, the same ones are drilled in the ceiling with a drill with a diameter of 3.5 mm. Then the cornice is laid aside, and the resulting holes are drilled to a diameter of 6 mm.
5. Next, dowels are driven into the resulting holes. This must be done in such a way that the edge of the dowel does not protrude from the hole. Then the cornice is installed in place and screwed in place.
6. Once the cornice is installed, you can hang the rest of the blinds on it.
7. If the ceiling is made of plasterboard, then it is advisable to attach the cornice to the sheathing profiles using self-tapping screws. If this is not possible, the cornice is attached directly to the drywall using a special dowel.
8. In some situations, it is not possible to attach vertical blinds to the ceiling, for example, if the latter is made of PVC film (so-called stretch ceilings). In this case, it is mounted on the wall using brackets. The curtain rod has special threaded holes, thanks to which brackets are attached to it.
9. The brackets themselves are mounted on the wall above the window opening. Before starting work, it is necessary to make markings for the level so that they are installed at the same height. The brackets are attached to the wall using dowels.

Dismantling

No matter how securely the blinds are attached, there comes a time when they need to be removed in order, for example, to clean them from dirt or repair them.

The process of removing vertical curtains:

1. Open and then collect the strips.
2. The weights are released.
3. Separate the panels from each other.

The process of removing horizontal models:

1. Free the cornice from the brackets.
2. Remove the decorative panel (if there is one).
3. Raise the panel and look for the protrusions of the fasteners.
4. The clamps are pulled towards you. Then they are pulled to the right.
5. The curtain is pulled down.
6. The structure is removed.

The process of removing roller blinds:

1. The tongue, which is on the bracket, is bent. To do this, use a screwdriver.
2. Remove the shaft.

Blinds that have become obsolete can be removed as easily as they are installed

Installation instructions

To hang blinds on tape or clips, you don’t need to drill holes, so you can handle the task yourself.

It is important that the brackets do not touch the moving part of the rollers and cords inside the curtain rod. Before installation, be sure to try on the fasteners and, in this form, attach the blinds to the window to mark the location of installation of brackets or clamps

Installation on tape

You can install regular and cassette blinds using tape, the only difference is in the fastening, the installation technology is identical

It is important to ensure reliable adhesion here, so the surface should be properly prepared:

• be sure to wash the window frame and dry it well so that dust and debris do not get under the tape;
• treat the installation site with a degreaser; according to reviews from experts and home craftsmen, acetone is best suited for this.

To hang a regular model, you need to attach special platforms to the profile. The adhesive tape is already glued to the parts; you just need to remove the protective layer and attach the pad in place to the prepared surface. Next, a holder with grooves is hung on it, onto which the cornice is fastened.

The diagram shows the installation of blinds on tape; the method is suitable for attaching light-weight structures

Horizontal cassette blinds are also installed using double-sided tape. The adhesive strip is located on the inside of the box on the top bar and on the sides

Here it is important to place the cornice evenly against the frame and press it tightly. To avoid distortions, it is recommended to put marks on top, which will serve as guidelines

Hanging blinds with tape with your own hands is very simple, but this method does not leave room for error. If the curtains are installed unevenly, you will have to remove the structure, tear off the tape and re-stick it. Be sure to watch the video tips from the master; he explains all the nuances of installing cassette curtain rods with tape.

How to hang blinds on plastic brackets

Plastic brackets for hanging blinds come in the form of hooks or brackets, it all depends on the design features of the cornice. The hooks are installed on the top of the frame, and brackets are attached to them in grooves, onto which the blinds are placed.

Diagram of how to attach blinds to hook brackets

The clips have a more rigid fixation and are suitable for installing small horizontal blinds, including pleated blinds. The cornice is placed at the installation site, pressed against the sash, and a bracket is placed on top, grasping two surfaces at once, like a paper clip on paper. The clamp should be pressed until there is a characteristic click, which indicates that the edge of the bracket has completely entered the groove of the cornice.

Features of installation on metal brackets

To install a metal bracket, you must first mark the space for the clamp. Then the base part of the bracket and the movable element are put on the sash and pressed on the front side with screws.

The diagram shows detailed instructions for installing horizontal blinds on brackets.

The video below shows how to attach blinds to different types of brackets; you can compare designs and choose the best option for yourself.

Methods for attaching roller blinds

When deciding how to install blinds on a window, the first priority is to determine the appropriate mounting method. The roll structure is mounted both on self-tapping screws and with the help of an adhesive (adhesive tape, liquid nails).

2 ways to attach roller curtains to a PVC window, to L-shaped brackets and to tape

In the first case, the technology for installing vertical curtains is taken as a basis, since roller blinds require fastening only in the upper part of the structure. To “plant” the structure on the adhesive, the surface of the windows is cleaned and degreased. This will improve the adhesion of materials.

In the first case, the technology for installing vertical curtains is taken as a basis, since roller blinds require fastening only in the upper part of the structure. To “plant” the structure on the adhesive, the surface of the windows is cleaned and degreased. This will improve the adhesion of materials.

How to hang on a window opening

The algorithm for installing blinds on a wall consists of several sequential steps:

First of all, you need to determine whether all components are available. If the blinds have a width of more than 2 m, then they must be supplemented with intermediate fastening. This eliminates sagging of the cornice. The next step is marking. To do this, the blinds are placed above the window in the right place. Then they retreat from the ends by about 3 cm and mark the locations of the brackets. When all the marks have been made, use a drill to drill holes for the dowels

It is important to choose the correct hole diameter in order to form a strong connection between the fastener and the wall. If the structure is wide, then you need to drill a hole in the middle in a similar way for an additional dowel. Please note that for heavy aluminum or wooden blinds, the distance of the end screws should be at least 10 cm from the edge of the cornice. When the brackets are screwed, the cornice is hung on them

It can be fixed in several ways. The most convenient mechanism is considered to be self-latching locks. Simpler products need to be screwed to the frame using self-tapping screws or self-tapping screws.

The process of installing blinds in the opening itself can be described by the following sequential actions:

Initially, the technical equipment of the product is checked. Pay attention to the size of the cornice. The method of attaching it depends on this. Assembling blinds The process is carried out in accordance with the manufacturer's instructions. Marking. To do this, the cornice is installed on the plastic window sash. Sometimes installation is possible on the ceiling of the opening or on the wall that is formed above the frame frame

When taking measurements, it is important to check whether the blinds do not interfere with the movement of the opening sashes. The mounting locations for the brackets are also marked on the base. After this, holes are drilled and fasteners are attached.

You should not drill deep, as you can make a through hole. If fixation occurs directly on plastic, special screws should be used. The process ends with hanging the cornice and canvas. This process is similar to that described in the previous section.

Wall or ceiling mounting

Before installing roller blinds, you must:

• check the kit, make sure all parts are present and in good condition;
• assemble the mechanism;
• Unwind the fabric completely, check for holes and other defects.

Hang with self-tapping screws

Self-tapping screws are the most reliable fastenings for roller blinds. The only drawback to using this type of fastener is the need to drill holes.

Installation of open-type curtains on self-tapping screws is carried out in the following order:

1. Attach the roller shutters to the mounting location.
2. Make sure the size of the roller blind matches and that it does not block the window handle.
3. Mark the locations for the holes.
4. Use a spirit level to check the correct position of the marks.
5. Use a drill to drill.
6. Insert dowels.
7. Secure the brackets with self-tapping screws.
8. Put on the side plugs.
9. Insert shaft.

The installation of the closed roller blind shaft is completed by installing the box.

Fastening with double-sided tape

If you don’t want to damage the wall by drilling, then double-sided tape is used to fix lightweight blinds. The fabric roller shutter kit may include a mounting strip with an adhesive layer covered with a protective film (the same as adhesive tape).

Fastening roller blinds with tape.

Features of fastening using double-sided tape:

1. Instead of marking the holes on the wall, mark the position of the curtain shaft.
2. The surface under the tape or mounting strip must be degreased. When choosing a product, you need to take into account the properties of the material from which the wall is made. Otherwise, marks may remain.
3. You should be especially careful when selecting a degreaser if the walls are covered with wood coated with varnish or paint.

Other options

If you need to hang fabric roller shutters on plasterboard sheathing, then during the installation process the frame under the curtain is reinforced with an additional profile or wooden block installed horizontally. Their length should be slightly greater than the width of the roller shutter.

Dowels for gypsum boards:

1. Knauf Harmut. They can withstand weights of up to 55 kg on a double-layer wall and up to 6 kg on a ceiling.
2. Umbrella. The disadvantage of fastenings of this type is that they cannot be dismantled. You have to be especially careful when marking.
3. Molly. They can be unscrewed. Molly dowels with a bolt and a hex head are suitable for hanging roller blinds.
4. Fisher PD and PDS.
5. Legs. These fasteners are screwed in with a screwdriver or screwdriver without drilling.

Driva plasterboard fasteners and butterfly dowels are not suitable for installing roller blinds. They cannot support the weight of the roller shutter.

Features of fastening fabric roller shutters to the ceiling

Attaching roller blinds to the ceiling is allowed if the distance from it to the window opening is up to 20 cm. In this case, the brackets are placed vertically. This is the only difference from the option with the roller shutter fixed to the wall. Only self-tapping screws matched to the ceiling material are suitable for fastening. Holes for dowels are drilled in the concrete, and the roller blind is screwed to the wood with screws 4 cm long.

Roller shutters are attached to a plasterboard or suspended ceiling in the same way as to a gypsum plasterboard wall - before covering the frame, an additional profile or beam is placed under the curtains. You can simply leave niches in front of the window openings and hang the roller shutters on self-tapping screws. To choose the appropriate option, it is better to look at the photo.

Curtains to the ceiling, already covered with plasterboard, are fixed to a corner, which is attached to the wall with one edge. Its width should be equal to the width of the roller shutter. The last option (only for gypsum board ceilings) is fastening with special dowels.

Progress of installation of blinds

After unpacking the blinds, read the instructions. Installing blinds means: measuring the window and adjusting the dimensions of the blinds to it; then install the fastenings for the cornice and cord system; assemble the strips onto the cornice and check the functionality of the system.

Measurements and markings

Measurements and markings

Measurements are necessary so that later it will be convenient to use the light-protective fabric without complaining about distortions or frequent breakdowns

It is especially important to check the dimensions of the canvases and adjust them to the place of attachment if the window opening has a specific geometric shape

Before screwing, you need to mark the position of the fasteners with a pencil, checking them with a level and a tape measure to avoid a skewed fit and leave room for adjusting the container, and also to ensure that the slats do not extend beyond the window glass.

Installation of cornice and slats

Installation of blinds

Before installation and actual installation, it is necessary to mark the fasteners with maximum accuracy and symmetry. Additional fastening must be provided for the control cord so that the structure can withstand the additional load. All elements are fixed to the wall with screws or dowels. Next is the installation of the cornice. The slats and runners themselves will be attached to it. The rigidity of the structure is guaranteed by the upper cornice strip, so there is no need to further strengthen the strip with glue, sealant or foam - it is fixed quite rigidly.

When re-installing, you need to measure the width of each window sash so that the window fittings do not interfere with the free hanging of the slats. Also, when choosing an installation “in the window opening”, you need to reduce the height on each side by 2 cm so that the canvas does not touch the window sill. To secure the blinds close to a plastic window, you need to drill the plastic window frame according to the markings - pre-drilling will prevent cracking of the plastic.

The height of the blinds must be no less than the height of the window opening

If the plates on which the blinds are hung do not fit tightly to the window profile, use pads.

Brackets for blinds are screwed into the holes using self-tapping screws. Next, you need to secure the brackets upward with latches and insert the container with the blinds into them.

Brackets for blinds are screwed into the holes using self-tapping screws.

Next, you need to secure the brackets upward with latches and insert the container with the blinds into them

The lower holders are attached like this: lower the curtain to mark the lower points (the canvas should be loosely stretched). Using these marks, drill holes into which you need to screw the lower holders that secure the canvas in the “micro-ventilation” position. Make sure that the staples sit firmly in the plastic.

When installing an overlay, you need to add 5cm in width so that the entire opening is closed. The height is adjustable and can reach the window sill or the floor itself.

There are a number of modern methods for installing blinds, which involve installing a cornice with slats on brackets attached to the window frame without drilling. The cornice with stripes is simply hung on the brackets and snaps into place. The design is collapsible, which allows you to remove the blinds when you need to wash the window glass or wipe the slats. This is the easiest way to install blinds.

Blinds on bracket

Features and purpose of blinds

The main characteristic of blinds is their simple installation, in which the product is quickly and easily fixed in the window opening. A convenient control process allows you to effectively change the level of illumination in the room.

When choosing blinds, you should decide not only on the appearance and material of the blinds, but also on the method of fixing them on a plastic window so that their operation is as efficient as possible.

Wide range of fabric slats for vertical blinds

The main element of blinds is the slats. They can be:

1. Vertical or horizontal.
2. Rolled or pleated.
3. Fabric, plastic, wood, aluminum.

Fixation methods

The location method varies:

1. Inside the window opening - in the trim.
2. On the sash of a plastic window.
3. Above the window opening. Fixation is made to the wall.

Note! When choosing between the first and second fixation methods, the width of the window sill and the depth of the window opening are taken into account. In the third case, the window opening is completely closed.

More information about types of blinds

The main function is to protect premises and furniture from direct sunlight. Traditional curtains can also cope with this task, but the advantage of blinds in this case is that they do not interfere with the circulation of fresh air, and also allow you to regulate the intensity of light in the room in a wide range - from complete darkness to filling the room with sunlight. You don't have to put in any special effort.

Blinds in the bedroom

Blinds can be used in many modern and some classic styles. Most of all, they correspond to the trends of minimalist interiors - they allow you to rationally use free space, do not require much space, and are easy to use and maintain.

Horizontal devices do not affect the functionality of the window system

Table 1. The most common types of blinds

Prices for blinds

Blinds

Installation of horizontal blinds on PVC window sashes

With this installation method, the blinds are attached with small self-tapping screws (included in the kit) to the window profile. They must be installed so that they do not interfere with the handle turning. Be careful: if you drill too close to the bead, you can damage the glass unit. Therefore, in this case, correct measurements are very important.

Installation of blinds on a PVC window

Installation step by step

The procedure is as follows:

• We install the fasteners on the cornice so that they do not interfere with the moving parts inside.
• Let's try the product on the frame. We set it so that the slats overlap the drain frame and the right at the same distance.
• Mark with a pencil or marker the place where the fasteners should be located. During this operation, you need to keep the cornice as level as possible. You can follow the contours of the window frame or use a level.
• Although the plastic is quite soft and you can immediately screw self-tapping screws into it to prevent the frame from cracking, it is better to pre-drill the holes. The diameter of the drill is slightly smaller than the diameter of the screws. Usually the kit comes with self-tapping screws with a diameter of 3 mm, so you need to take a 2 mm or 2.5 mm drill.
• We take the brackets and fasten them to the frame with self-tapping screws.
• Insert the blind rod, pressing until it clicks.
• We close the ends with the plugs that come with the kit.

Having to drill holes in a window frame can be intimidating, but it's no big deal. In case of incorrectly made holes, the unsuccessful ones can be filled with sealant. White silicone, not acrylic (acrylic quickly turns yellow). The performance of the windows will not be affected. What can be dangerous is getting into a double glazed window. Then it may crack. But this is not fatal either - it can be replaced, although it will not be cheap.

We install the lower clamps

But that is not all. To finally install horizontal blinds on plastic windows, you need to drill a couple more holes - for the clamps (also called anti-wind). These are additional fastenings at the bottom of the opening window sash. The lower edge of the blinds is tucked into them. They do this so that when ventilating, the blinds do not hang down, dangle in the wind, or knock over objects on the windowsill.

Don't hang out...

We install the clamps like this: we try them on, pulling the blinds down a little, mark the fastening points, drill holes, and install them. We tuck the bottom bar into the installed clamps. Now, even with a draft or an open shutter, the blinds will not dangle. The only thing you need to watch out for during installation is not to get caught in the glazing bead (this is a long strip that runs along the glass unit and holds it in place). It is necessary to drill a hole in the frame itself, stepping back at least 1 cm from the edge. Otherwise there are no problems.

No drilling

There is also a way to install blinds on plastic windows without drilling the frame. This method is only available for those blinds that are hung on opening sashes. In this case, they are simply hung on plastic mounts/brackets, which are placed on the frame from above. To prevent them from moving, a strip of double-sided tape is attached to the back of the bracket. After removing the protective film, you can glue it (but you don’t have to fix it).

The shape of the plastic fasteners depends on the type of cornice. So you need to select it specifically for each

These L-shaped plastic brackets are not included, but can be purchased at a store or company that sells horizontal blinds. This method is convenient by simply dismantling the blinds, which is convenient if they need to be repaired or washed.

Fastening without screws

Typically, such fasteners are used in rented areas, when the appearance of the windows cannot be spoiled.

We will need:

• Scissors.
• Double-sided tape.
• Set of blinds.
• Pencil.

Work progress

• Unpack the package.
• We remove the adjustment bar so that it does not interfere.
• Place the block with the wrong side up.
• We measure the length of the tape equal to the length of the body.
• Cut off the excess tape.
• We remove the protective strip and stick it on the wrong side of the block.
• We try on the location of the blinds relative to the window sashes.
• We mark the points where the ends of the blinds will be attached.
• Remove the protective strip and glue the top part.
• We press the profile well to the surface.
• We install the adjustment bar.
• We check the operation of the structure.

Important! The width of the tape should be approximately equal to the width of the block. We smooth out the tape so that there are no blisters; it should lie evenly over the entire surface.

Installation of horizontal blinds

A huge plus of horizontal blinds is that they can be installed on plastic windows of any shape, even roof windows are no exception.

Installation on a frame is an ideal option for horizontal slats, allowing you to open and close windows separately or simultaneously.

To install horizontal slats, you need to stock up on a screwdriver, a screwdriver and marking material (chalk, pencil or alcohol-based felt-tip pen).

Having decided on the mounting method, proceed to the following steps.

Find out the dimensions of the window (measure the width and height).

• If you are going to install blinds in the first way - in the window opening - you should subtract 2 centimeters from the height. This way you will achieve a result when the slats do not touch the window sill.
• If you chose the third method - attaching the blinds with an overlay - add 5 centimeters to the width, but always on each side. In this case, the height is determined by the desires of the owner.
• Installing blinds on windows (on each sash) is considered the simplest and easiest method of installation. The dimensions of the window must be measured taking into account the fittings, that is, so that they do not limit the window or touch it.

Unpack the blinds. Assess their quality, inspect for defects, and check the components. Everything is in place? Place the blinds against the window

It is important that the body fits between the boundaries of the beads on both sides of the glass. Pull the blinds tighter. They must be in the same plane as the window. Assess the overall situation

The blinds should be located at the top of the transparent area. Visually record the presence of a gap, which very often forms between the fastening elements and the window sashes. The size of the gap can be different and vary from a few millimeters to a couple of centimeters. They do not depend on the correctness of your actions; these are rather the costs of the design of the window and double-glazed window. Manufacturers foresaw the possible risk and, to correct the current situation, equipped the blinds with linings and special elements that allow them to achieve the required thickness and reduce the distance between the fastening elements and the window sashes.

Be sure to pay attention to the marks on the base of the linings. They can be of two types: R (from the English word right) and L (left)

Right and left application respectively.

• Fix the gaskets until a tight clamp is established. Then secure them in the gap between the fastening elements and the window field.
• Mark the fastening.

The geometric shape of the curtains is the main guideline for marking. Be sure to check that nothing prevents the window from opening and closing. Install an additional fastener where the cord is adjusted.

You can attach the blinds using one of two options.

1. Bead fastening. A very delicate process that requires care in choosing the length of the screws. An incorrectly chosen length is the first step towards depressurization of the glass unit, the result is a violation of the thermal insulation properties.
2. Attaching to a profile is a simple and safe process, but it requires care and precise actions.

Install the blinds using long screws. It is advisable that you use the self-tapping screws included in the kit. The aesthetic appearance of the window after installing the curtains depends on them. This step must be taken with great care.

Install the cornice, runners, slats

Place the decorative cornice on the mechanism and secure the plugs on the sides. Using a drill (diameter should be 3 millimeters), make a hole for the plastic “fungi”, they are located in the lower edge of the bead. This will allow you to install the guide line. After pulling it tight, secure it and cut off the excess.

Control step - checking the functioning of the entire structure

How to take correct measurements

In order to correctly install blinds on plastic windows, it is important to make accurate measurements, which are related to the installation technology.

Measurements of each plastic sash in the apartment are taken separately, even if it seems that the parameters of the window openings are the same. Often the difference is still present - it is not noticeable to the naked eye.

In the window opening

If you plan to install it in a window opening, no matter what kind of blinds are attached, it is important to measure the parameters of the window so that the curtains hang freely and do not catch the window sill with the bottom edge.

To hang on the frame of a plastic window, measure the glass units horizontally. Then measure the height and subtract 2 cm from it.

On the ceiling or wall

To attach blinds to a wall or ceiling, you need to decide in advance on the length of the curtains (they can end at the level of the window sill, under it, or reach the floor), and note at what level they will end.

Next, mark the area where you plan to hang the cornice. Now you can measure the distance from the top mark to the bottom. This is the required curtain length.

To hang a curtain on the wall and ceiling, the width of the curtain fabric must exceed the width of the window opening by at least 50 mm on the sides. However, this parameter may be larger.

If the window sill is wide enough so that the curtain hanging at the level of its edge does not interfere with the opening of the sashes, then the structure can be hung directly on the wall. If the plastic window is flush with the wall, then the blinds will have to be hung on additional fasteners that increase this distance. Otherwise, the curtain will prevent the windows from opening and impair the ventilation of the space.

On the doors

This installation requires careful measurements. In this case, you will have to measure each sash separately, in addition, preliminary adjustment of the plastic windows will be required.

First measure the width and height of the glass. Add 50 mm to the length (25 mm at the bottom and top). Add 30 mm to the width (15 mm on each side). This margin will be enough so that the slats completely cover the glass, but do not interfere with the opening of the plastic window.

If the handle is located too close to the glass, then no increase in width is made.

Installation of vertical blinds

Anyone can install such curtains with their own hands. If the blinds are short, they can be placed inside the window openings. Otherwise, installation is carried out on the wall or under the ceiling.

For error-free fastening, sequential instructions are given:

Step 1:Marking

The central point of the window opening is determined and correlated with the center of the blind cornice. You need to make marks along the edges of the structure with your own hands. Points for installing self-tapping screws are marked on both sides of the cornice closer to the center of the window block by about 5-6 mm.

Place the cornice against the wall so that the center of the cornice coincides with the center of the window, and make marks along the edges.

Step 2:Look by level

At the same time, you need to evaluate whether the slats are positioned correctly. Their lower part should be 1-2 cm above the floor level. The same amount must be retreated when installing short curtains (up to the window sill).

Step 3:Attaching the Brackets

Dowels are installed in holes prepared in advance with your own hands. The brackets are secured, this is done using self-tapping screws. Next, special clips are installed on these elements.

Be careful when using the hammer drill when drilling for bracket fastenings, otherwise part of the wall may break off. Step 4:Installing slats and chain

Step 4:Installing slats and chain

A cornice is attached, into which all that remains is to insert the runners and hang the vertical slats directly on them. The final touch is attaching the chain.

The slats must be hung in the exact order in which they are folded in the package. Otherwise, the design of the blinds may be damaged.

Preparation, taking measurements

The following tools will be useful: a screwdriver/screwdriver, a tape measure, a carpenter's pencil. In order for your curtains to function as efficiently as possible, you need to take the correct measurements. The structure should be located symmetrically relative to the glass unit.

If blinds are attached using adhesive tape without drilling, it is possible to correct errors. For analogues installed on brackets and screws, you need to mark as accurately as possible.

To fasten vertical curtains, it is enough to measure the dimensions of the window opening, the distance between the fastening points and the length to the bottom edge of the curtain. This will allow the structure to be correctly positioned relative to the level of the floor and window opening.

What is a plastic window

Before proceeding with the instructions for attaching blinds to a PVC window, it is necessary to explain what a standard PVC window is. After all, it is on the plastic itself that blinds are often hung.

In fact, blinds can be mounted on the wall (on the opening), between the slopes (in the opening) and on the frame itself. But in this article we will tell you how to attach it to a frame or sash. Read more about other methods here.

Most people are afraid of damaging a plastic window by drilling. In order to install blinds correctly without fear, we will provide the necessary information about the design of a plastic window.

Fastenings without drilling either reduce the thermal insulation characteristics of the window by jamming the seal, or, like adhesive tape, are intended for very light products and often have a short service life. We recommend installing blinds on plastic windows with drilling.

To install blinds on a plastic window you need to know:

1. A plastic window can be solid or with a sash.
   If half of your window is solid and the other with a sash, then usually in the first case they are mounted on the frame, in the other - on the sash.
2. The frame, that is, the frame, and the sash are made of a plastic multi-chamber profile with metal reinforcement inside.
   Reinforcement can make drilling and fastening more difficult.
3. Glazing beads come in different shapes: rounded, beveled, shaped.
   To attach blinds to a glazing bead, special compensating wedges are sometimes used.
4. The glass unit goes deep into the frame to the depth of the glazing bead.
   This means that you cannot damage the glass in any way when drilling the frame.
5. The frame is made of a multi-chamber profile.
   There is a hole on the outside of the frame to remove condensate.

The hole does not affect the freezing of the window. Freezing can be facilitated by a “cold bridge,” for example, a metal pin passing through the entire thickness of the frame. The self-tapping screws used to attach the blinds occupy only 1 chamber, without creating a risk of freezing.

Plastic window device

Thanks to the voids inside the frame, low thermal conductivity is ensured. Therefore, plastic windows retain heat better. But drilling holes will not be able to ensure such air movement inside so that the heat leaves faster.

The fit of the sash to the frame is ensured by a seal